background image

           Ducting & Exhaust                       Argo Service Manual

Ontario Drive & Gear Limited                                                                                               www.odg.com
PH.(519)- 662-2840   FAX (519)- 662-2421

DE-6

Assembling and Installing the Muffler Assembly (Conquest Models)

1.

On an 

uncluttered 

 work surface, orient the muffler heat shield assembly with the

rubber shock lower support, to the back.  Insert the muffler into the shroud with the
exhaust inlet situated to the right.    Photo DE-15

DE-15

DE-16

3.

Reinstall the 2 lower fasteners to secure the muffler at the bottom of the shroud.

Photo DE-17

2.

Turning the tailpipe end of the shroud around to face the assembler will put the

tailpipe also to the right side of the shroud.  Photo DE-16

4.

Flip the assembly over and secure the muffler at the exhaust inlet end.
Photo DE-18

DE-17

DE-18

5.

Secure the heat shield with the appropriate hardware.  Refer to your illustrated parts

manual for correct hardware and orientation.  Photo DE-19

6.

Install the assembly into the vehicle at 90 degrees, compressing the rubber mounted

lower support to ease the installation and provide enough clearance in the engine
compartment.  Photo DE-20  Set the assembly on to the front wheel well temporarily

Summary of Contents for 6x6 Conquest

















Reviews: