ENGLISH
• To prevent electric shock and fire, do not immerse the device in water or other liquids. If this happens, DO NOT operate the product,
immediately disconnect it from the power supply and contact the Service Center for inspection.
• Do not use a hair trimmer with damaged comb or one of the teeth - this may result in personal injury.
• Unplug the appliance if you are not using it before cleaning.
• Be extremely careful if there are children or persons with disabilities near the operating device.
• Do not use outdoors.
• Save this instruction manual.
ATTENTION: REGULAR
LY
LUBRICATE THE BLADES.
• Do not use the trimmer for skin inflammations.
• Do not trim the animals with the hair trimmer.
• ATTENTION! Disconnect hand held parts from the power cord before cleaning them in water.
• The manufacturer reserves the right to make minor changes to the design of the product without further notice, not fundamentally
affecting its safety, performance and functionality.
- The appliance is suitable for cleaning under
running water.
BATTERY CHARGING
- Insert one end of the USB cable into the connection hole and the other into the network adapter
with the suitable specifications
(not included
into
the set
).
- Place the hair trimmer on a flat, stable surface.
- Connect the network adapter to the network, the charging indicator will light up.
- It takes 2 hours for full charge of the battery.
- A fully charged battery operates approximately 60 minutes.
- After the battery is charged, the charge indicator will turn off. Unplug the power adapter and disconnect the USB cable from the hair trimmer.
ATTENTION:
- Charge the battery at a temperature not lower than + 5 ° C and not higher than + 35 ° C.
- If you have not used the hair trimmer for a month or more, fully charge the battery before using the device.
- Do not leave the device connected to the network unattended.
CUTTING BLOCK LUBRICATION
Before first use, lubricate the cutting unit with the oil supplied.
- Apply oil to the contact points of the movable and fixed parts of the blades.
- Turn on the hair trimmer and let it run for approximately 30 seconds to distribute the lubricating oil over rubbing surfaces.
Turn off the hair trimmer, remove excess oil with a dry cloth or paper towel.
Note:
- Lubricate the cutting unit after each use of the hair trimmer.
- Use only the oil supplied or oil intended for similar devices.
Do not use vegetable oil or oil that contains solvents. Solvents are subject to evaporation, and the remaining oil will slow down the speed of the
blades.
OPERATION
• Press on / off
switch
. Make sure the cutting unit is perpendicular to your skin, move the block while making reciprocating movements.
Use both edges of the blade to create sharp lines and perfect edges.
• To detail whisker, the area around the mouth or nose, hold the hair trimmer so that one of its edges touches the blade skin. This technique allows
you to create sharp edges or lines.
• When finished, turn off the trimmer by pressing the on / off
switch
.
• After each use of the device, clean the shaving unit using a cleaning brush.
DETACHABLE HEAD USAGE
The detachable head allows you to adjust the height of the hair from 0.5 mm to 10 mm.
• Before the first use it is recommended to set the maximum height - 10mm. For further usage you can set the required height of the remaining
hair from 0.5 mm
up to 10 mm.
• Install the detachable head on the cutting unit until it is fully locked. Select the desired hair height by scrolling the height regulator counterclockwise.
• While cutting make sure that the flat part of the detachable head is in full contact with the skin to achieve even hair cutting.
CLEANING, MAINTENANCE AND STORAGE
TRANSPORTATION. Transportation of the device is necessary by any kind of covered transport with the application of cargo securing rules
ensuring preservation of the presentation of the product and / or packaging and its further safe operation. DO NOT expose the device to shock
loads during handling operations.
CLEANING. ATTENTION! Never wash parts in a dishwasher. Do not use chemicals or abrasives. Always unplug the appliance before cleaning.
• Remove the detachable head. After remove the cutting unit by pressing the cutting unit release button.
• Using a brush for cleaning, remove any remaining hair from the cutting unit and detachable head. You can also rinse the cutting unit and
detachable head under running water. Caution: Do not immerse the trimmer, USB cable in water or any other liquids.
• Wipe the haur trimmer body with a soft, slightly damp cloth, and then wipe it dry.
STORAGE. The device must be stored indoors, in conditions that presume the preservation of the presentation of the product and its further safe
operation. Make sure that the appliance and all its accessories are completely dried, before storing it. To avoid damaging the cord, do not wind it
on the body.
BATTERY REMOVING
• Before disposing of the device, remove the battery from it.
• Before removing the battery, disconnect the device from the mains.
• The battery must be disposed of safely.
RECYCLING
The appliance and packing materials must be disposed with the least harm to the environment and in accordance with the rules for waste disposal
in your area.
WARNING: Do not use this appliance near bathtubs, showers, basins or other
vessels containing water.
