manualshive.com logo in svg

Arecont Vision AV1195DN, Installation Manual, Page: 19 / 29

Share
Download
Arecont Vision AV1195DN Installation Manual Download Page 19

  

 

Installation Manual 

 

 

Page | 19       [email protected] 

 
 

 

+1.818.937.0700    877.CAMERA.8    www.arecontvision.com    [email protected] 

Mega

Video® Flex

 

SD Card Tab 

Menu

 

Feature

 

Description 

 

 

Playback 

Allows the user to choose the specific time of video to playback. 

 

Click to Play 

Button to play video specified in the 

Playback

 field. 

Continuous Recording 

Allows the user to continuously record without restriction. 
Default is unchecked box.  

Stop Continuous 
Recording AND Enable 
Event-triggered 
Recording 

Allows the user to enable events recording when network 
failure, motion alarm, or an I/O alarm is triggered. Default is 
unchecked box. 

NOTE: if the continuous recording is disabled and no event 
recording is enabled, the SD card will not initiate recording.  

Network Failure 

Allows the SD Card to record video only in the event that the 
network fails. 

Motion Alarm 

Allows the SD Card to record video only in the event that motion 
is detected. 

I/O Alarm 

Allows the SD Card to record video only in the event that an I/O 
alarm is triggered. 

Recording Framerate 

Allows setting a frame rate output limit for the H.264 video 
stream. Default value is “Max” minimum fps is 1. Reducing the 
frame rate output is another way to control the bandwidth used 
for the H.264 video streaming from the camera trade off is the 
obvious reduction of frame rate output at the camera. Options 
are 0 to 30. No default. 

SD Card Image 
Resolution 

Provides the ability to set the resolution. Options are 

Full 

or 

Half

. 

Half 

is the default.  

Start 

Shows the beginning time frame of the video being recorded. 
No default.

 

End 

Shows the ending time frame of the video being recorded. No 
default.

 

Delete All Records 

Allows the user to delete any previously recorded video on the 
SD card. 

Summary of Contents for AV1195DN






























Reviews:

No comments