manualshive.com logo in svg

Arecont Vision AV1195DN, Installation Manual, Page: 10 / 29

Share
Download
Arecont Vision AV1195DN Installation Manual Download Page 10

  

 

Installation Manual 

 

 

Page | 10       [email protected] 

 
 

 

+1.818.937.0700    877.CAMERA.8    www.arecontvision.com    [email protected] 

Mega

Video® Flex

 

Mounting the Main Unit

 

1.  Determine a secure location to mount the main unit from the camera. There is a 40ft. maximum 

distance from the camera to the main unit.  
 

 

 

Mount Procedure for Drywall/Masonry 

     Mount Procedure for Metal Application 

                

 

Ref #

 

Description 

 

For Drywall/ Masonry Applications 

1 

Prepare surface for installation by placing the main unit where desired and marking each of 
the four the holes with a pencil.  

 

 

2 

Drill the appropriate size holes to install 4x of the #6-

32 1” Drywall/ Masonry Mounting 

Anchors (Ref #2) where you marked the pencil holes.  

3 

Place the holes of the main unit over the Drywall Mounting Anchors and use a Philips head 
screwdriver to screw 4x of the #6-32 1.5

” Wood/ Metal Sheet Screws (Ref #3).

 

For Metal/Wood Sheet Applications 

4 

Prepare surface for installation. Then, insert the 4x #6-32 1.5

” Machine Screws (Ref #4) 

through the each of the four holes on the main unit. 

 

5 / 6 

Thread a #6-32 Washer (Ref #5) into each Machine Screw and then fasten securely with a 
#6-32 Hex Nut (Ref #6) on each.

 

Summary of Contents for AV1195DN






























Reviews:

No comments