background image

www.spacesgate.com

SG-1 Quick Installation Guide

FCC

Federal Communication Commission interference statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of 
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee 

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the 
separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. 

RF Exposure Warning

The equipment complies with RF exposure limits set forth for an uncontrolled environment. The antenna(s) used for this 
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void 

your authority to operate the equipment.  

FCC Caution

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
          (1) this device may not cause harmful interference and
          (2) this device must accept any interference received, including interference that may cause undesired operation
This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your 
body.
Notice: Any changes or modifications not expressly approved by the party responsible for compliance could void your 

authority to operate the equipment.

CE

Hereby, AREC Inc., declares that this Media Station is in compliance with the essential requirements and other relevant 
provisions of Directive 2014/53/EU.

01

CB

CAUTION
Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

– the ventilation should not be impeded by covering the ventilation openings with items, such as newspapers,table-cloths,
    curtains, etc.: 
– no naked flame sources, such as lighted candles, should be placed on the apparatus;
– attention should be drawn to the environmental aspects of battery disposal;

– the use of apparatus in tropical climates.

the instructions for use shall state that the apparatus shall not be exposed to dripping or splashing and that no objects filled 
with liquids, such as vases, shall be placed on the apparatus.

Summary of Contents for SpacesGate SG-1













Reviews: