background image

 

 

outdoor use may cause decrease efficiency and damage to the unit

 

 

Avoid installation in a high humidity and/or dusty area

 

humidity could cause unit to rust and decrease efficiency of the unit 

dust collected on condenser coil will cause unit to malfunction. Clean the condenser at least 

once a month with a brush or clean cloth 

 

Select a location away from heat and moisture-generating equipment

 

high ambient temperature will cause the compressor to overwork, leading to higher energy 

bills and gradual breakdown of the unit

 

  The appliance shall not be exposed to rain, sun 

 

The cabinet must not be located in a chloride / 
acid-containing environment (swimming-bath etc.) due to 
risk of corrosion. 

 

CAUTION: PROBLEMS CAUSED BY UNPROPER 

POSITION OF UNITS ARE NOT COVERED BY 

WARRANTY     

 

 

  The castor is with a brake, turn it to different side can lock or unlock the castor 

   

   

 

 

 

 

 

       

     

ELECTRICAL SAFETY 
 

 

Please ensure that the required voltage of the compressor is being supplied at all times 

CAUTION: Low or high voltage can detrimentally affect the refrigeration unit. 

 

All units should be plugged into a grounded and properly-sized electrical outlet with 

      appropriate overcurrent protection. Please refer to the electrical requirement on the 

nameplate. 

If you do not have the right outlet have a certified

 

electrician   

install the correct power source. 

 

Summary of Contents for FPHEF968
















Reviews: