Architect 1600 SE Professional Installer'S Consciousness Manual Download Page 35

Page: 35 / 36

Architect

Model 1600 SE

Model 1601 SE

installer’s Guide

™

1600 SE Series Specifications

High Current Amplifier

Amplifier Power Rating

. . . . . . . . . . . . . . . . . . . . . 60 Watts @ 8 ohms

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

150 Watts @ 4 ohms

Bridged Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 Watts @ 8 ohms

Minimum Speaker Load . . . . . . . . . . . . 4 ohms (2 ohms limited zones)

Damping Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Greater than 200

Total Harmonic Distortion . . . . . . . . . . . . . .0.09% (Full Power, 20-20k)

Input Sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Variable 0-1 Vrms

Input Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 kilohms

Crosstalk . . . . . . . . . . . . . . . . . . . . . . . . . . . Greater than 80dB @ 1kHz

Equalizer Center Frequencies . . . . . . . . . . . .75, 250, 700, 2.5k, 12KHz

PFM Highpass Filter . . . . . . . . . . . . . . . . . . . . . . . . . 40Hz (switchable)

Remote Power Trigger . . . . . . . . . . . . +12 VDC or Dry Contact Closure

AC Main Fuse Rating . . . . . . . . . . . . . . . . . . . . . . . . 2 x 8 amp Slo-Blo

AC Main Operational Voltage . . . . . . . . . . . . . . . . . .95 volts - 130 volts

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 pounds (23 kg)

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17” W x 16” D x 7” H

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . 19” Brackets (4U high)

Network Connection (Model 1601 SE) . . . . . . . . . . . .10BaseT Ethernet

Network Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TCP/IP

Communication Protocol . . . . . . . . . . . . . . . . . . . . . . . . HTTP or Telnet

IP Addressing . . . . . . . . . . . . . . Selectable Static or Dynamic via DHCP

Default Static IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . 192.168.0.1

US Patent Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5,708,577

Specifications

This manual was written, designed, printed, folded and stuffed into the box in
the U.S.A. Probably on a really soggy day considering where we live.

Summary of Contents for 1600 SE





































Search results

Summary of Contents for 1600 SE

Reviews:

Brands by name

Popular brands

Architect 1600 SE, Professional Installer'S Consciousness Manual

Search results

Summary of Contents for 1600 SE

Reviews:

Brands by name

Popular brands