background image

O

per

at

e

E-22

Setting up rCube-to-rCube transmission

With two rCubes, one rCube can receive wireless 
transmissions from the other.

Any music played on the transmitting rCube, from an iPod or 

an external source, will be sent wirelessly to the second rCube. 

Before transmitting for the first time, you must associate the 

transmitting rCube with the receiving rCube.

After an association is established it is remembered, even 

if the units are powered off. Note: Association must be 

performed twice if you want each cube to be able to transmit 

to the other - you will need to repeat the steps below with the 

cubes switched around. Once this is done, you’ll be able to set 

either cube to receive whatever the other is playing.

I

O

1

 

Power on all rCubes

Connect power, turn on at the rear panel and 

power on using the top panel standby buttons, so 

that the power LED glows blue.

2

 

Set the 

transmitter

 rCube to search for 

receiver rCubes 

Press and release the source select button to select 

the source (iPod or AUX) that you want to 

transmit. Press and hold the wireless button 

until the wireless LED flashes red. For the next 

30 seconds this transmitter rCube will associate 

with any rCube searching for an association 

(see step 3).

3

 

Set the 

receiver

 rCube(s) to search for a 

transmitter

Press the wireless button to select the wireless input.  

Release the button briefly, then press and hold. 

The wireless LED will flash red as it searches for a 

transmission. When the wireless LED on the rCube 

glows continuous green, the association has been made. 

Wireless Range

An rCube can normally receive from a 

transmitter situated in the same house. 

Range may be reduced depending on 

building materials and interference from 

other wireless sources such as cordless 

telephones and WiFi routers. If you 

experience problems with the wireless 

signal, try moving either the receiving 

rCube or the transmitter to a different 

location. Wireless operation cannot be 

guaranteed in hostile RF environments.

The transmitting rCube will continue 

to search for receiver rCubes for 30 

seconds. Do not interrupt this process – 

wait until the wireless LED glows green 

before powering off the transmitter 

rCube.

Summary of Contents for RCUBE



























Reviews: