background image

O

per

at

e

E-21

Playing from the rWand Optional iPod Transmitter 

I

O

2

NOTE: You need to associate each cube with a wireless transmitter before that 

cube can receive the transmitter’s audio.

1

 

Install the rWand iPod transmitter into your iPod, iPhone or iPad.

Plug the rWand transmitter into the docking connector at the bottom 

of your Apple player. You can check to see if the rWand is broadcasting 

by looking at its LED, which will flash briefly every five seconds when 

transmitting.

2

 

Power up

Plug the power supply into the AC mains wall supply and the DC power 

input jack on the rear panel of the rCube. Switch on the rCube by pressing 

power switch on the rear panel, and press the top panel standby button. 

The blue power LED should light. 

 

     

Select the rWand as wireless source

To select the rWand iPod transmitter, press the ‘Wireless’ button 

on the remote control or on the top panel. If a source is available the light 

will turn green and the source will begin to play. Note: if a second wireless 

source is also transmitting you may have to  press the ‘Wireless’ button 

twice to select the correct transmitter. 

4

 

Play tunes on the iPod/iPhone/iPad

NOTE: Some Apple devices require you to select the iPod music player 

application.

5

 

Adjust volume

Use the + and - volume buttons on the remote or on the top panel to adjust 

the volume to desired level. The rCube volume can also be adjusted using 

the iPod’s volume control.

MENU

,

.

;4

Summary of Contents for RCUBE



























Reviews: