ARB 3417100 Fitting Instructions Manual Download Page 1

 

 

20/05/2014 

Page 1 of 10 

3782968 

If you have any queries regarding the installation of this product please contact the distributor from whom it was purchased, or alternatively the ARB office in your state. 

Head Office – ARB Corporation Ltd VIC:

 42-44 Garden Street, Kilsyth, Victoria, 3137 Tel: (03) 9761 6622 Fax: (03) 9761 6807 

WA: 

(08) 9244 3553  

NSW:

 (02) 9821 3633  

ACT:

 (02) 6280 7475  

SA:

 (08) 8244 5001  

QLD:

 (07) 3872 3872  

NT:

 (08) 8947 2262  

TAS:

 (03) 6331 4190

 

 
 
 

NISSAN GU PATROL WINCH BULL BAR. 

(SRS AIR BAG EQUIPPED MODELS) 

PRODUCT NUMBER 3417100 / 3417110 

 

 

 

WARNING 

FOR VEHICLES EQUIPPED WITH SRS AIRBAG 

WHEN INSTALLED IN ACCORDANCE WITH THESE INSTRUCTIONS, THE FRONT 

PROTECTION BAR DOES NOT AFFECT OPERATION OF THE SRS AIRBAG. 

 

TAKE NOTE OF THE FOLLOWING: 

 

 

THIS PRODUCT MUST BE INSTALLED EXACTLY AS PER THESE INSTRUCTIONS USING 
ONLY THE HARDWARE SUPPLIED. 

 

 

IN THE EVENT OF DAMAGE TO ANY BULL BAR COMPONENT, CONTACT YOUR 
NEAREST AUTHORISED ARB STOCKIST. REPAIRS OR MODIFICATIONS TO THE 
IMPACT ABSORPTION SYSTEM MUST NOT BE ATTEMPED. 

 

DO NOT USE THIS PRODUCT FOR ANY VEHICLE MAKE OR MODEL, OTHER THAN 
THOSE SPECIFIED BY ARB. 

 

 

DO NOT REMOVE LABELS FROM THIS BULL BAR. 

 

 

THIS PRODUCT OR ITS FIXING MUST NOT BE MODIFIED IN ANY WAY. 

 
 
 

Summary of Contents for 3417100











Reviews: