manualshive.com logo in svg

ARB 2237010, Fitting Instructions Manual

Share
Download
ARB 2237010 Fitting Instructions Manual Download Page 11

20/08/2014 

Page 11 of 15 

Fitting instructions# 3789248 

Copyright © 2005 by ARB Corporation Limited.  All rights reserved, this document must not be reproduced without the express authority of ARB Corporation Ltd 

 

WING INSTALLATION 

 

 

 

37.  Using the M12x35 fine thread bolts,flat 

washers, spring washers and flange nuts, bolt 
the wing to the centre section aligning al the 
front faces and tighten . 5 per side. 

 

 

     

 M12 - 77 Nm. 

 

 

 

 

38.  Fit the wing braces from the centre section to 

the wing, using the M10 x 30mm SEMS and 
Flange nuts. 4 per side. 

 

 

39.  Ensure there is a parallel gap between the 

body and the top face of the wing of around 
15mm. The chassis mounts may have to be 
loosened to achieve this. Tighten all bolts to 
specified torque. 

40.  Connect the Fog light loom to the vehicle 

harness and closest fog light. Feed the loom 
through the large rubber grommets and 
connect to other fog light. Cable tie loom to 
wing brace and centre section. 

 

 M10 - 44 Nm. 

 

 

 

Summary of Contents for 2237010
















Reviews:

No comments

Brands by name

Popular brands

Load more brands