ARB 2237010 Fitting Instructions Manual Download Page 1

Page: 1 / 15

20/08/2014

Page 1 of 15

Fitting instructions# 3789248

Part Number:

2237010-2237020-2237030

Product

Description: Modular Bar

Suited to DODGE RAM 2500/3500 2012 on

vehicle/s:

WARNING

REGARDING VEHICLES EQUIPPED WITH SRS AIRBAG;

When installed in accordance with these instructions, the front protection bar does not affect operation
of the SRS airbag.

ALSO, NOTE THE FOLLOWING:



This product must be installed exactly as per these instructions using only the hardware

supplied.



In the event of damage to any bull bar component, contact your nearest authorised ARB

stockist. Repairs or modifications to the impact absorption system must not be attempted.



Do not use this product for any vehicle make or model, other than those specified by ARB.



Do not remove labels from this bull bar.



This product or its fixing must not be modified in any way.



The installation of this product may require the use of specialized tools and/or techniques



It is recommended that this product is only installed by trained personnel



These instructions are correct as at the publication date. ARB Corporation Ltd. cannot be held

responsible for the impact of any changes subsequently made by the vehicle manufacturer



During installation, it is the duty of the installer to check correct operation/clearances of all

components



Work safely at all times



Unless otherwise instructed, tighten fasteners to specified torque

ARB 4x4 ACCESSORIES

Corporate Head Office

42-44 Garden St

Tel:

+61 (3) 9761 6622

Kilsyth, Victoria

Fax:

+61 (3) 9761 6807

AUSTRALIA 3137

Australian enquiries

[email protected]

North & South American enquiries

[email protected]

Other international enquiries

[email protected]

www.arb.com.au

Summary of Contents for 2237010
















Search results

Summary of Contents for 2237010

Reviews:

Brands by name

Popular brands

ARB 2237010, Fitting Instructions Manual

Search results

Summary of Contents for 2237010

Reviews:

Brands by name

Popular brands