background image

 19

t

roUbLeSHooting

 

and

 

faQ

S

Unit will not turn on.

Make sure the power washer is in the “OFF” position.  Plug in the 

electrical cord to a grounded 120 volt outlet (no electrical extension 

cord should be used).  If the electrical cord will not plug into your 
outlet, your electrical outlet is not properly grounded and should not be 
used.  Use another electrical outlet.  Press the reset button on GFCI 

power box.  If the color of red is not visible in the little window on the 

GFCI, unplug and plug in again. Press reset, and look for the red color 
in the window, this should remain red in color.  If the color is staying 
red, turn the power switch on the power washer to “ON”.  Squeeze the 
trigger on the spray gun and try again.
If this did not correct the problem, try plugging into another electrical 
outlet and repeat the above procedure. If it is still not working, call 
Customer Service at 1-866-235-5112.

The high pressure (HP) 
hose will not connect / 
stay connected to the 
spray gun.  Is this a 
spray gun problem?

In most cases, the spray gun is not the problem.  The problem is the 

rubber sleeve covering the fitting at the end of the high pressure hose. 

It has likely slipped up toward the metal tip.  The fix: wiggle, twist and/

or pull the rubber sleeve down until the entire tip is visible plus an 1/8” 

of the metal fitting below the tip.  Now try to insert the hose tip into the 

spray gun.  It should “click” into place and will not come out until the 
hose is released by pushing in the lever on the underside of the gun.
You may cut away the end of the sleeve with a sharp knife if unable to 
move the sleeve down.  Be careful not to cut or puncture the hose.

The unit is running but 

there is not water flow.

Check the water source.  Unclog the nozzle on the lance. (See nozzle 
cleaning instructions under “Cleaning nozzles”.)  Or take off the lance 
and just spray out of the spray gun.  This will indicate if the problem is 
with the lance.

Why is water leaking 
where the high pressure 
hose connects to the 
spray gun?

Make sure there is an o-ring at the end of the metal tip of the high 
pressure hose.  If no o-ring is present, the connection between the 
hose and spray gun will leak.  O-Ring Kits are available online at www.
arblueclean.com or call Customer Service at 1-866-235-5112 to place 
an order.

I can’t remove the lance 
from the spray gun. 
What should I do?

All lances and the detergent tank are attached and removed from the 
spray gun in the same manner.  Insert the quick-release end of the 
lance/detergent tank into the spray gun.  Press the spray gun and 
lance together (about a 1/8”) and turn clockwise.  The lance will lock 
in place.  Remove the lance by reversing this procedure.  Press the 
spray gun and lance together and turn counter clockwise.  The lance 
will slide out.  Or, hold the spray gun and lance in an upright position 

with the nozzle end on the floor.  Push the whole assembly straight 

down to loosen the connection, and then follow the removal process 
again. You may also spray soapy water or a lubricant in the area 
where the lance connects to the spray gun.

The power washer turns 
on for 2 seconds, shuts 
off, and will not turn 
back on. Do I have a 
defective unit?

It sounds like your power washer is working just fine.  When the water 

is connected, the accessories are assembled properly, and the power 
switch is turned on, the power washer may turn on for 1 - 2 seconds to 
prime the pump. It automatically shuts off and waits for the spray gun 

trigger to be pressed.  When the trigger is pressed, water starts flowing 

through the pump. The water sensor in the pump “senses” the moving 
water and automatically turns the power washer on.  Or, turn the power 
switch to off, hold in the trigger on the spray gun, so that you have a 
steady stream of water. While you are holding the trigger open on the 
spray gun, at the same time, turn the power switch on.

Summary of Contents for AR383S





















Reviews: