background image

AQ1B Underwater Metal Detector User Manual

13

AQ.4.061

AQ1B Bonephone – Fully waterproof headphone,
utilises Ikelite underwater connector to connect to
the AQ1B Control Module. Normally placed
against the skull at the back of, or below the ear
whilst underwater, enabling the diver to clearly
hear the change in the Detector tone when metal
is sensed

AQ.4.062

AQ1B Bonephone with Extending Flexible
Cable– Fully waterproof headphone, utilises
Ikelite underwater connector to connect to the
AQ1B Control Module. Normally placed
against the skull at the back of, or below the ear
whilst underwater, enabling the diver to clearly
hear the change in the Detector tone when metal
is sensed. Comes with extendable flexible cable
which allows more freedom of movement with
the Bonephone whilst underwater.

AQ.4.030

AQ1B Land Headphones – Rugged
headphones for use above water
enabling The AQ1B to be utilised as
a powerful land detector. The
Headphones feature an adjustable
volume control and a comfortable fit
for the user.

 

AQ.4.031

AQ1B Underwater Headphones –
Rugged headphones for use
underwater giving an alternative to
the Bonephone. These are
particularly useful in warm waters
where a diving hood is not normally
worn, They also provide a more
powerful sound level that can
enhance the ability to sense even the
most subtle changes in the audible
output.

AQUAPULSE 1B SYSTEM PARTS & ACCESSORIES

Summary of Contents for AQUAPULSE 1B



















Reviews: