background image

General Safety   . . . . . . . . . . . . . . . . . . . . . . . .
Getting Started  . . . . . . . . . . . . . . . . . . . . . . . . 
Testing and Controls   . . . . . . . . . . . . . . . . . . .  
Setup/ Pre-Set Flow Valve   . . . . . . . . . . . . . . 
Troubleshooting    . . . . . . . . . . . . . . . . . . . . 
Aquafog Fan Exploded View   . . . . . . . . . 
ORSM Tank Exploded View   . . . . . . . . . . 
Maintenance   . . . . . . . . . . . . . . . . . . . . . . . . . 
Warranty    . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2

PAGE     

3

 4
 5

6

7 - 8

9 - 10

 11 - 12

13
14

T

ABLE

 

OF

 C

ONTENTS

Notes

D

ESCRIPTION

Aquafog mobile units are intended to condition large  

volumes of air using water or other non-hazardous 

liquids at air temperatures between 31ºF and 145ºF. 

Any other use of these units will void the warranty 

and the manufacturer will not be responsible for 

problems or damages resulting from misuse.

S

AFETY

 G

UIDELINES

This manual contains very important information. 

This information will help ensure SAFETY and 

PREVENT EQUIPMENT PROBLEMS. Use these 

symbols to understand safety guidelines.

DANGER

DANGER INDICATES AN 

IMMINENTLY HAZARDOUS 

SITUATION WHICH, IF NOT AVOIDED, WILL RESULT IN 

DEATH OR SERIOUS INJURY.

WARNING INDICATES A 

POTENTIALLY HAZARDOUS 

SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN 

DEATH OR SERIOUS INJURY.

CAUTION INDICATES A 

POTENTIALLY HAZARDOUS 

SITUATION WHICH, IF NOT AVOIDED, MAY RESULT IN 

MINOR OR MODERATE INJURY.

NOTICE INDICATES IMPORTANT 

INFORMATION, THAT IF NOT 

FOLLOWED, MAY CAUSE DAMAGE TO EQUIPMENT.

WARNING

CAUTION

NOTICE

Summary of Contents for SE-ORSM-1500















Reviews: