23
ORDERING REPLACEMENT PARTS
To order replacement parts for the AquaCraft TS3 use the order
numbers in the replacement parts list that follows. Replacement
parts can be purchased from your local hobby shop or by mail
order. If you need assistance locating a dealer to purchase parts,
visit
www.aquacraft.com
and click on “Where to buy”.
If you are missing parts, contact Hobbico Product Support at:
Phone: 217.398.8970
Fax: 217.398.7721
E-mail: [email protected]
REPLACEMNET PART NUMBERS
AQUB0007 ......TS3 Tunnel Hull, Orange
AQUB0008 ......TS3 Tunnel Hull, Yellow
AQUB0009 ......TS3 Tunnel Hull, Red
AQUB0010 ......TS3 Tunnel Hull, White
AQUB9005 ......Throttle Cable Outboard 36" with Pushrod Tube
AQUB9782 ......Steering Linkages
AQUB9047 ......Transom Cover
AQUB6897 ......Fuel Tank Mount
AQUB6229 ......Cowl Orange
AQUB6230 ......Cowl Red
AQUB6231 ......Cowl Yellow
AQUB6232 ......Cowl White
AQUB6330 ......Decal Sheet
AQUB7899 ......Engine Mount Plate, Aluminum
AQUB8602 ......Radio Box with Lid, Servo Tray
AQUB9506 ......Rubber Hull Plugs
AQUB9535 ......GrimRacer Fuel Tank
AQUB6899 ......O-Rings for Fuel Tank Mount
AQUB7802 ......L-Link Pushrod Connector
AQUB9503 ......Radio Box Seal Boots
AQUB9537 ......GrimRacer Antenna Mount
AQUB9505 ......Antenna Exit Boot Seals
AQUB9509 ......Foam Pad
DRIVING AND RACING TIPS FROM 12-TIME
NATIONAL & WORLD RACING CHAMPION
MIKE “GRIMRACER” ZABOROWSKI
GrimRacer Says:
Don’t just drive your TS3
around, drive your TS3 around something! To
reach the full potential this boat has to offer,
you need to get it on the water running around the race course.
Running your boat on the race course allows you to build depth
perception as well as get to know the needs of the boat.
➧
The TS3 responds best if you drive it as if you were driving a car
or any other type of wheeled vehicle. Your lap times will go down if
you lift off the throttle and set the boat as you enter the corner and
accelerate out. Driving “white knuckled” you will likely not be paying
attention to your entry point, losing valuable seconds off your lap time.
➧
If the pond you test at has an elevated driver’s platform, make sure
you stand on it even during testing. Also stand in multiple locations.
This way if you do not get your favorite spot on race day, you will not
be surprised by what you experience. It is also good to take a quick
look at the water and race course before you launch the boat for
your heat. If you see a buoy out of place or an obstacle in the water,
it’s best to identify it before you launch the boat.
➧
Starting and launching the boat later in clock time is far better
than starting and launching at the beginning. If your clock time is
2:30 like most, be warned, if you go out early you are adding to the
seconds your boat can get into trouble. During the race it’s best to
be on the water ONLY as long as you need to be.
➧
Also have your caller show you the back of the boat before he or
she launches it. Move your rudder back and forth and make SURE it
is working before he or she launches the boat.
NATIONAL ORGANIZATIONS & ON-LINE HELP
www.impba.net
www.namba.com
www.aquacraftmodels.com
www.futaba-rc.com
www.osengines.com
www.odonnellracing.com
www.intlwaters.com
www.rcuniverse.com
www.rcgroups.com
www.metimeliverc.com
OS Max 21
Transom Top
Transom Bottom
C
L
