background image

5

 ❷ Installati on

  

 2.1 I  Setup

Hose length necessary

: Cleaner
: Twist Lock Hose 

secti ons

: Pool valves
: Sucti on line
: Skimmer 
: Filtering pump 
: Filter

 Sucti on line connecti on example

  

 2.2 I  Twist Lock Hose secti on assembly

2.2.1 Determine the number of secti ons you need

•  Measure the length between the sucti on line or the skimmer and the furthest away point of the pool.

•  Add an extra 1 metre to the length measured.

•  If total length is over 10 metres (MX

TM

6-MX

TM

630) or 12 metres (MX

TM

8-MX

TM

8 PRO), contact your reseller to purchase 

any additi onal Twist Lock hose secti ons required for your pool. 

: Connecti on to the sucti on line or 

the skimmer

: Hose length necessary
: 1 metre secti on of Twist Lock 

hose with fl oat

: Connecti on to the cleaner

Tip: insert the "right" quanti ty of Twist lock hose secti ons 

Inserti ng  more  Twist  Lock  hose  secti ons  than  the  length  necessary  to  cover  the  whole  pool  is  not 

recommended. Hoses that are too long may limit the cleaner's performance.

2.2.2 Twist Lock Hose secti on assembly

•  To assemble two Twist Lock hose secti ons, insert them then turn them unti l the connectors are at the maximum stop 

point, in one of the 3 notches that provide the seal (see image  )

.

•  The secti on of Twist Lock hose with the hose fl oat att ached will be connected to the cleaner (see image  ). The Twist 

Lock hose fl oat must be located 

20-23 cm away from the cleaner.

 (see image  ).

20-23 cm

Float

Summary of Contents for ZODIAC MX 6

















Reviews: