To connect:
Cut end of
tube square
Insert and
seat fi rmly
Press and hold
collet against
fi tting, pull tube
out of fi tting
340 mm
60 mm
Vertical
Clearance
To disconnect:
2. The Quick Connect Push-In system
All fi ttings provided for the water tubing
are “Quick Connect Push-In Fittings”,
which do not require any tools or
sealing materials.
3. Decide where your Aqua-Pure
®
system should be
installed before working out how.
Choose a suitable area within the cupboard under the
sink to mount the water fi lter system see
fi
g
1.
fi g. 1
INSTALLING YOUR WATER FILTER SYSTEM
fi g. 2
WATER SUPPLY
The installation of your Aqua-Pure
®
water
fi lter system requires access to cold water feed from a
standard 1/2” or 3/4” BSP tap, such as that used for
dishwashers and mixer taps (ref fi g 2).
Option A
3/4” BSP tap
Option B
1/2” BSP tap
CAUTION:
This fi lter must be connected to cold water line only. If the dishwasher is connected
to hot water, you cannot proceed to connect the water fi lter system to this hot water supply.
HELPFUL HINT:
If there is insuffi cient room in your cupboard to install the water fi lter
system vertically, it can safely be tilted up to 60 degrees clockwise or anti-clockwise.
1. Turn water supply tap off and remove dishwasher/mixer tap connecting hose
from
tap.
fi g. 3
3. Remove black stopper plug from the Multi-Function
Control Valve (MFCV) (3) (ref fi g 4) and screw adaptor
1/4” BSP x 1/4” tube (5) into side outlet port of MFCV
(3) until it is tight enough so it will not leak (ref fi g 5).
4. Thread tape and attach brass nipple (6) to the bottom part of MFCV
(ref fi g 6).
fi g. 4
fi g. 5
Option A (ref fi g 2)
a. Screw MFCV (3) onto
3/4” water supply tap
with inlet spinning nut.
Ensure rubber washer
is fi tted into tap entry
nut. Hand tighten
suffi ciently to avoid
leaking (ref fi g 7).
Option B (ref fi g 2)
a.Take MFCV (3) and with
an 8mm hex key, unscrew
inlet nut by inserting hex
key into key provision in
inlet. Once in place, turn
hex key anti-clockwise to
unscrew adaptor nut
(ref fi g 8).
b. Screw MFCV to water
supply tap. Hand tighten
suffi ciently to avoid leaking
(ref fi g 9).
fi g. 8
fi g. 9
fi g. 7
fi g. 10
CAUTION!
Do not overtighten MFCV
5. Reconnect dishwasher hose to end of MFCV (3) (ref fi g 2).
6. If you do not have a dishwasher or a mixer tap, screw the black
stopper plug removed in above and screw into the end of the
MFCV (3) (ref fi g 10).
fi g. 6
fi g. 11
fi g. 12
MOUNTING THE SYSTEM
7. Mark location of fi xing holes (ref fi g 11) and fi x unit
to cupboard with two of the mounting screws
provided (ref fi g 12). Remember, approximately
60mm space must be provided below the bottom of
the cartridge, to allow removal.
8. Remove protective red cap from cartridge (2). Align centre of label
on cartridge with inlet on head (1), push cartridge into head fi rmly
and turn to right (ref fi g 13).
fi g. 13
INSTALLING YOUR ALL-IN-ONE MIXER TAP
1. If applicable, remove your existing mixer tap and both the cold and
hot braided hoses (ref fi g 14).
fi g. 14
2. Unpack the new all-in-one mixer tap (9), new braided hoses and fi ttings from their
packaging.
3. Attach the new cold water braided hose (blue), hot water
braided hose (red) and fi lter water hose to the
all-in-one mixer tap as per diagram shown (ref fi g 15).
4. Feed all three of the braided hoses (one at a time) through
the round opening on your sink.
5. Attach the threaded rod to the base of the all-in-one mixer
tap and hand tighten it all the way.
6. Locate the mixer tap on the opening on your sink, slide the
stainless steel anchor plate through the threaded rod and
hand tighten the brass retainer nut (ref fi g 16).
Cold Water
Filter Water
Hot Water
Mounting
Hole
fi g. 15
fi g. 16
BATTERY INSTALLATION
1. Carefully remove the black rubber LED timer housing from the
all-in-one mixer tap (9) handle (ref fi g 19).
fi g. 19
2. Reset / new installation:
Insert a new CR2032 size button battery into the LED timer housing
with positive facing outwards (ref fi g 20).
NOTE:
• Use a new CR2032 battery.
• When correctly installed, you will observe the Red light fl ashing
twice, followed by a single blue fl ash
.
fi g. 20
3. Install LED timer housing into fi lter tap handle’s opening
(ref fi g 21).
fi g. 21
4. When mixer tap is turned ON, the blue LED will start fl ashing
(ref fi g 22).
fi g. 22
7. With the all-in-one mixer tap facing in the desired direction, tighten
the brass retainer nut fully using suitable sized spanner /
adjustable wrench (ref fi g17).
fi g. 17
8. Attach the cold water braided hose (blue) to the cold water tap; attach the hot
water braided hose (red) to the hot water tap.
9. Attach all-in-one mixer tap hose adaptor (8) to the end of the fi lter
water hose. This fi tting does not require thread tape and should be
fi nger tightened, followed by a further ¼ rotation using suitable
sized spanner / adjustable wrench (ref fi g 18).
fi g. 18
2. Thread tape adaptor 1/4” BSP x 1/4” tube (5) with thread tape
(11) supplied (ref fi g 3).
