background image

Set Up Instructions

Setting up the Protein Skimmer 

For the following section refer to Diagrams 1 & 
2 on pages 5 & 6 of this instruction booklet.

1. Set the Protein Skimmer Air Pump (18) in the 
cabinet next to the MariSys or on top of it. It is 
recommended that the Air Pump always be 
positioned higher than the wooden airstone. 
Your MariSys is supplied with a Check Valve, 
this ensures water does not back siphon into 
the Protein Skimmer Air Pump. This allows you 
to place the Air Pump on the base of the cabinet 
next to the MariSys. 

Please Note: All attachments are inserted into 
the Airline during production. Simply attach the 
blue adapter to the Protein Skimmer Air Pump 
and the other end to the Protein Skimmer 
Airline Connector (19). Step 2 can be ignored 
during set up and referred if needed at a later 
date during maintenance.

2. Connect one end of the airline tubing to the 
Protein Skimmer Airline Connector (19) and the 
other end to Check Valve (20). Connec the 
second piece of airline tubing from the Check 
Valve to the Air Control Valve (21), and then the 
third from the Air Control Valve to the blue 
adapter which fits over the 2 outlets of the 
Protein Skimmer Air pump.  

3. Connect the Waste Hose (22) to the outlet at 
the base of the Protein Skimmer Collection Cup 
(23), then place the other end of the tubing into 
an empty 1 litre Container. (Not supplied) (24) 

4. The height of the wooden airstone has been 
preset; the bent portion on the rigid tubing of the 
Airline Connector is at the recommended 
setting.

To raise or lower the airstone, grasp the rigid 
tubing and gently turn left or right while pushing 
down or pulling up. 

If the airstone is positioned too high in the 
Reaction Chamber, (25) the air bubbles will 
overflow and fill the Collection Cup. Under 
normal conditions, the airstone should be 
positioned about 1.5 – 2cm from the bottom of 
the Reaction Chamber. 

The aquarium’s water level can also be raised 
or lowered by adjusting the Water Level 
Adjuster. (10) Raising the tube will cause the 
aquarium’s water level to rise and lowering the 
Water Level Adjuster will cause the aquarium’s 
water level to drop. 

3. Remove the pre-filter pad, rinse it under 
water and place back into the Overflow Box. 

4. Turn the Screw Adjuster (11) located at the 
bottom of the Overflow Box to level it. 

5. Position the Priming Pump (12) with hanger 
next to the Overflow Box on the aquarium’s rim. 
Connect one end of the airline tubing to the 
Priming Pump “in” (13) port (indicated by the 
arrow which points towards the Priming Pump 
on the red connection adapter). Connect the 
other end of the airline tubing to the V-Joint (14) 
located at the top of the Water Bridge. (15) 

6. Connect the second piece of airline tubing to 
the “out” (16) port of the Priming Pump 
(indicated by the arrow pointing away from the 
Priming Pump on the red connection adapter) 
and secure the other end of the airline back into 
the aquarium. It is very important to ensure this 
hose does not dislodge as it will drain the 
aquarium.

7. Measure the distance from the Overflow Box 
to the MariSys.  Be accurate so you do not cut 
the hose too short. (Measure twice and cut 
once) Take the utility knife and cut the Large 
and Small Flexible Hosing (17) to the desired 
length.

The Flexible Hosing must follow a straight path 
from the Overflow Box to the MariSys. There 
can be a little slack but not too much or the filter 
will not operate correctly. 

8. Place a Hose Clamp over the end of each 
piece of Flexible Hose and slide the Flexible 
Hosing over the outlet and inlet, located on the 
base of the Overflow Box. Do not tighten the 
Hose Clamps yet.

9. Do the same for the connections at the top of 
the MariSys. 

10. Once every thing is in position tighten the 
hose clamps so it is a snug fit. DO NOT OVER 
TIGHTEN them as you may crack the plastic.

8

Summary of Contents for MariSys 240
















Reviews: