background image

— Page 9 —

© 2008 Aqua-Hot

®

 600-D Hydronic Heating System Installation Manual

Installing the Expansion Tank:

  

Select a mounting location that allows for easy access 

and clear visibility whenever the particular storage bay 

door is open.

NOTE:

 The top of  the expansion tank should always be 

mounted at least 4 inches higher than the highest point 

on the Aqua-Hot. Reference Figure 11.

1. 

Mount the expansion tank as illustrated in Figure 11.

2.  Connect and clamp the overflow tubing from the 

expansion tank to the Aqua-Hot’s expansion tank con-

nection.  Reference Figure 11.

Figure 11

NOTE: Avoid any dips and bends in the overflow tubing from 

the Aqua-Hot to the expansion tank as air can become 

trapped in these dips and bends, preventing the expan-

sion of  the heating solution from properly depositing 

into the expansion tank.

3.  Drill a hole in the bay floor and connect (secure with a 

clamp) a long enough piece of overflow tubing so that 

it can be connected to the top of the expansion tank 

and extend through the bay floor.

Fill to “Cold” level 

mark with “GRAS” 

approved 50/50 

antifreeze/water 

mixture.

Air-Release Valve

Expansion Tank 

Connection

Expansion Tank

Mount top of expansion 

tank at least 4 inches 

higher than the Aqua-Hot.

Overflow Tubing

section 1: aqua-Hot Installation

Overflow tubing from 

expansion tank to hole 

drilled in motorhome floor.

Summary of Contents for 600-D
























































Reviews: