background image

13

CARE OF YOUR LIFT

Routine cleaning is an absolute necessity to ensure the integrity of the lift. Note that the
Aqua Creek Pool Lift should not be stored in a pump room or in a storage room where
pool chemicals are kept. Storing the lift near pool chemicals may cause rusting and other
damage to occur. Your Aqua Creek stainless steel lift is powder coated to protect the
stainless steel from rusting. Most rusting will occur at weld points, crevices, under
gaskets, rivets or bolt heads.

The choice of a proper cleaning product is up to the consumer and there are many to
choose from. Depending on the type of cleaning and the degree of contamination
(rusting), some products are better than others. For routine cleaning the products most
recommended are gentle soaps or detergents or dilute mixtures of ammonia. For
stubborn spots and stains try using soft scrub with some brisk rubbing.

DO NOT USE POOL WATER TO CLEAN USE ONLY FRESH
WATER

If the lift is used

DAILY

make sure to wash the lift at the end of the day. Wash the lift

off using a mild soap and a soft cloth. Make sure to pay special attention to weld points
and crevices. Do not use a bristled brush or steel wool to clean the lift. Check that the
lift is working properly and then place the battery on the charger. It is recommended that
the battery be charged after every day of use.

If the lift is used

WEEKLY

follow the same steps as above. Also be sure to check all of

the contact points (terminals) for damage or corrosion. If you notice corrosion gently
clean the terminals. To clean corrosion from the terminals use a q-tip and some rubbing
alcohol. If the corrosion is particularly stubborn try using a 3M scotch brite pad, but be
careful not to damage the terminals. Apply dielectric grease to the terminals after
cleaning them. This will help to prevent further corrosion. Do not leave the battery on the
lift. Always store the battery on the charger whenever the lift is not being used.

SAFETY & MAINTENANCE INSTRUCTIONS

Do not play on or around this lift

1. Check the Pro Pool-XR before each use to assure there are no worn parts and that

all hardware is properly tightened. If there are any worn parts, replace them
BEFORE using the Pro Pool-XR. You can call our customer service at 1-888-
687-3552 to order any parts.

2. Aqua Creek Products, LLC lifts shall be grounded per local codes.
3. At least ONCE A WEEK, the Pro Pool-XR must be cleaned with fresh water. Do

not spray the Pro Pool-XR 24v battery unit directly with any pressure. Wipe all
surfaces clean with a damp, non-abrasive cloth. When cleaning the Pro Pool-XR,
use non-abrasive soap and water. Avoid harsh chemicals and disinfectants.

4. Always read the label instructions on any cleaner carefully before applying it to a

surface.

5. The WARNING & INTENDED USE labels on the Pro Pool-XR need to be

maintained in readable fashion. If they become unreadable or faded, please
replace the label immediately. Replacement labels are available from AQUA
CREEK PRODUCTS LLC. 1-888-687-3552.

Summary of Contents for F-004PLB-XR-R





















Reviews: