APRILIA RSV4 Factory a-PRC 2009 Service Station Manual Download Page 214

Page: 214 / 521

Error cause

•

An oil sensor fault is signalled when, with engine off, it is detected that the sensor circuit is

open. The test is performed only once when the key is set to ON. There is an error when

the general warning light turns on.

Troubleshooting

•

Check the sensor connector and the instrument panel connector (PIN 17): if they are not

OK, restore. If OK, check continuity of the purple cable between the sensor connector and

the instrument panel connector PIN 17: if not OK, restore the cable harness; if OK, replace

the sensor.

DSB 08: Oil pressure

Error cause

•

An oil sensor fault is signalled when, with engine running, it is detected that the sensor circuit

is closed. There is an error when the general warning light turns on.

Troubleshooting

•

Check if oil pressure is low with the specific gauge.

Neutral sensor

Function

It tells the gear position to the control unit, from the

1st gear to the 6th gear, and if the gear is neutral

or riding.

Operation / Operating principle

The sensor has 2 circuits: one to indicate the en-

gaged gear, whose resistance varies according to

the engaged gear: in this way, the injection ECU,

according to detected electric voltage, identifies

the engaged gear and sends the information via

CAN to the instrument panel; the other indicates

neutral gear, whose voltage is taken to zero if in

neutral position.

Level in electrical circuit diagram:

Start-up enabling switches

Location:

•

on the vehicle: under chain pinion, be-

hind the pinion cover.

Electrical system

RSV4 Factory a-PRC

ELE SYS - 214

Summary of Contents for RSV4 Factory a-PRC 2009










































































































































































































































































































































































































































































































































Search results

Summary of Contents for RSV4 Factory a-PRC 2009

Reviews:

Related manuals for RSV4 Factory a-PRC 2009

Brands by name

Popular brands

APRILIA RSV4 Factory a-PRC 2009, Service Station Manual

Search results

Summary of Contents for RSV4 Factory a-PRC 2009

Reviews:

Related manuals for RSV4 Factory a-PRC 2009

Brands by name

Popular brands