Applied Membranes W-G3072ET Operation, Maintenance & Instruction Manual Download Page 28

Page: 28 / 32

Installation and Service Manual – Carbon Filter

Page 28

Troubleshooting

PROBLEM

POSSIBLE CAUSE

SOLUTION

Inlet pressure low

Low supply pressure

Correct incoming supply pressure

Low flow from source

Remove blockage or other restrictions

Treated water flow low

Media/Resin bed fouled

Backwash Filter

Valves closed

Check valves and fully open

Untreated water is being
delivered

Bypass valve is open or faulty

Fully close bypass valve or replace

Media is exhausted due to high
water usage

Check program settings or diagnostics for
abnormal water usage

Water quality fluctuation

Test water and adjust program values accordingly

Damaged seal/stack assembly

Replace seal/stack assembly

Control valve body type and
piston type mismatched

Verify proper control valve body type and piston
type match

Fouled media bed

Replace media bed

No Display on PC Board

No Power at electrical outlet

Repair outlet or use working outlet

Control Valve Power Adapter
not plugged into outlet or power
cord end not connected to PC
board connection

Plug Power Adapter into outlet or connect power
cord end to PC Board connection

Improper Power Supply

Verify power voltage is being delivered to the PC
Board

Defective Power Adapter

Replace Power Adapter

Defective PC Board

Replace PC Board

PC Board does not display
correct time of day

Power Adapter plugged into
electric outlet controlled by light
switch

Use uninterrupted outlet

Tripped breaker switch and/or
tripped GFI

Reset breaker switch and/ or GFI switch

Power outage

Reset time of day. If PC Board has battery backup
present the battery may be depleted. See Front
Cover and Drive Assembly drawing for
instructions.

Defective PC Board

Replace PC Board

Control valve regenerates at
wrong time of day

Power outage

Reset time of day. If PC Board has battery backup
present the battery may be depleted. See Front
Cover and Drive Assembly drawing for
instructions.

Time of day not set correctly

Reset to correct time of day

Time of regeneration set
incorrectly

Reset regeneration time

Summary of Contents for W-G3072ET































Search results

Summary of Contents for W-G3072ET

Reviews:

Related manuals for W-G3072ET

Brands by name

Popular brands

Applied Membranes W-G3072ET, Operation, Maintenance & Instruction Manual

Search results

Summary of Contents for W-G3072ET

Reviews:

Related manuals for W-G3072ET

Brands by name

Popular brands