Applent Instruments AT824 User Manual Download Page 26

Page: 26 / 52

AT824/825/826 Handheld LCR Meter

5.1.1

Comparator [COMP]

Comparator formula:

100

⋅

−

Nom

Tol

Rx: Test Value

Nom: Nominal Value

USB Command: COMP <ON | OFF | 0 | 1>



Procedure to turn[COMP]on:

Step 1

Press[SETUP]to enter setup page

；

Step 2

Select[Auto Parameters]

；

Step 3

Off

Comparator off

Comparator on

5.1.2

[BEEP]Set

Use the beep to indicate test result pass or fail.

USB Command: COMP:BEEP <OFF | PASS | FAIL>



Procedure to set beep

Step 1

Press[SETUP]to enter <SETUP> page

Step 2

Select[BEEP]

Step 3

OFF

Turn Beep feature Off

Pass

Beep while Pass

Fail

Beep while Fail

5.1.3

Input Nominal Value [NOM]

Three ways to input nominal value:

Use touch screen[Keypad Input]

Nominal components measure[Measure Input]

USB Command: COMP:NOM <Floating Points >



Procedure to input nominal value:

Step 1

Press [SETUP] key to enter <SETUP> page

；

Step 2

Select[NOMINAL]

Step 3

Keypad Input

Use touch screen to type in

Meas Input

Measure a standard component as nominal



How to use touch screen to input nominal value

Summary of Contents for AT824





















































Search results

Summary of Contents for AT824

Reviews:

Applent Instruments AT824, User Manual, Page: 26 / 52

Search results

Summary of Contents for AT824

Reviews: