Apollo Radius Owner'S Manual Download

Page: 16 / 72

Updated 23/05/07

RAOM0507

Apollo Bicycle Company Pty. Ltd. ABN: 60 001 914 469

11. Safety & Accessories

- Check that all reflectors are attached correctly

and visible

- For riding at night, fit fully functioning dynamo

or battery powered lights

- Check that the bell is fully operational

- Check all additional components on the bike

are appropriately secured and functioning

- Ensure the bicycle rider and any passenger

in a child seat are wearing helmets

HELMETS

When riding your bicycle it is recommended that
you always wear an appropriately fitting, Australian
Standards Approved bicycle helmet. This also
applies to any passengers you may carry in a child
safety seat.

A bicycle helmet must:

- carry the Australia & New Zealand Standards

approved mark AS/NZS 2063 label

- fit properly

The helmet should be:

- well ventilated

- comfortable

- lightweight

The wearing of helmets is mandatory
in most Australian states. Non-
compliance may result in an
enforceable penalty.

Summary of Contents for Radius









































































Search results

Summary of Contents for Radius

Reviews:

Related manuals for Radius

Brands by name

Popular brands

Apollo Radius, Owner'S Manual

Search results

Summary of Contents for Radius

Reviews:

Related manuals for Radius

Brands by name

Popular brands