![background image](http://html.mh-extra.com/html/trp-cycling/hd-t910-tt/hd-t910-tt_installation-instructions_1173628001.webp)
SAFETY WARNINGS & INFORMATION
TRP Cycling Components
688 W. Amidan Dr. 4X-1
Ogden, UT 84404
Toll Free: 1-877-807-4162
Direct: 1-650-965-4442
Email: [email protected]
Web: www.trpcycling.com
HD-T910 TT Hydraulic
INSTALLATION INSTRUCTIONS
HD-T910 Flat-Mount Rear Adaptor & Bolt Lengths
HD-T910 Flat-Mount Rear 160 Rotor
Brake levers may be swapped to achieve
desired ergonomics. Please see online
videos at www.trpcycling.com
HD-T910 Flat-Mount
160 Rotor
HD-T910 Brake Lever
HD-T910 Flat-Mount
140 Rotor
HD-T910 Flat-Mount Adaptors Orientations
13
32
34
34
13
14
34
70
B
A
A
B
A
FF-6 R160 Adapter
FF-5 F140/F160 Adapter
Lever reach can
be adjusted via
2mm Hex
WARNING
- This braking system was designed for use on a single rider bicycle. Use of this system on any other vehicle or apparatus will void the warranty, possibly causing
you great personal harm or injury.
WARNING
- Disc brakes, calipers and rotors get VERY HOT during regular use. DO NOT touch or attempt to service the rotor or caliper assembly until you’ve allowed for
sufficient cooling to occur.
WARNING
- These disc brakes offer a significant increase in performance over traditional cable actuated systems. Follow the break-in recommendations listed in this
manual, allow yourself time to learn and become accustomed to the braking characteristics.
WARNING
- Leaking oil indicates a potential BRAKE FAILURE. If you’re system is leaking oil stop immediately and determine the nature of the problem. DO NOT continue
to ride a leaking system.
WARNING
- If your bike is involved in a fall or crash, fully check the brake function including: the lever, caliper and rotor are securely attached to the bike, pads are
correctly installed and functioning, the cable, (if applicable) is operating smoothly and the lever feels firm when applying the brake. Always have a qualified mechanic
check the brakes if you have any doubts.
WARNING
- Pad thickness must be at least 0.8mm of pad material. Confirm this before each ride. Keep pads clean and free of oil or hydraulic fluid. If pads become
contaminated, discard and replace.
CAUTION
- Read this manual completely before attempting to install or work on your TRP brakes. If you are unfamiliar with any element of assembly or maintenance of this
braking system please consult a qualified mechanic for assistance.
CAUTION
- Only use TRP or TEKTRO branded replacement Mineral Oil when servicing the brakes. Other disc brake fluids, ESPECIALLY DOT based oils, will harm the system
and compromise braking performance.
CAUTION
- Cleanliness is a very important part of any maintenance of a TRP disc brake. If the pads or rotor become contaminated with oil, or if the system becomes
contaminated with impurities, braking performance will be greatly impaired.
CAUTION
- As with any oil, precautions in handling and clean up of any spills should be handled according to accepted best practices as governed by your state or
country. Our Mineral oil is non-toxic, but clean up any spills promptly and completely.
If Mineral Oil gets in your eyes IMMEDIATELY FLUSH WITH WATER for several minutes and go to the hospital. If Mineral oil gets on your skin RINSE IMMEDIATELY with soap and
water. Do not inhale Mineral Oil, it is harmful. If inhaled move to a well ventilated environment and proceed to the hospital for appropriate care. If you ingest Mineral oil it
may cause vomiting and/or diarrhea.
TRP hydraulic disc brakes are warranteed against manufacturing defects in materials and / or workmanship for a period of two years from the date of original retail purchase.
Not covered under this warranty is damage resulting from improper installation, adjustment or maintenance, lack of maintenance, alterations, crashes or use judged by TRP
to be excessive or abusive. For warranty related questions or more information please contact a TRP Service Center or email at [email protected]