background image

Updated 23/05/07

RAOM0507 

 Apollo Bicycle Company Pty. Ltd.  ABN: 60 001 914 469

DRIVETRAIN

The drivetrain consists of the pedals, chain, 
chainwheel, crank set, and freewheel.   
These are all the components of the bicycle  
that transmit power to the rear wheel.  

Pedals

There is a vast range of pedals available, designed 
for many different uses.  Pedals fitted with toe clips 
and straps aim to make the pedalling process easier for the rider.  The toe clips and straps 
ensure the cyclist’s feet stay correctly positioned and cause a pulling force, as well as a 
downward pressure, to be generated on the pedals.  To get the full benefit of these pedals 
it is recommended that the rider wear cycling shoes especially designed for use with toe 
clips.  Consult your bicycle dealer for instruction on how toe clips and straps operate.

WARNING: 

Pedals fitted with toe clips and straps require a certain level of skill to operate 
safely.  Riders should repeatedly practice using such pedals in areas free from 
traffic, hazards or obstacles, until operation becomes a reflex action.   
Failure to do so could result in the cyclist losing control of the bicycle  
and falling.  It is also recommended that the straps be kept loose initially  
and gradually tightened as the rider’s skill in using the pedals increases.  
However, toe straps should never be tight when riding in traffic.

Inspection

Every month the pedals should be inspected.  Check that:

-   Pedals are securely fastened into the cranks.  Loose pedals are a potential hazard  

for both the rider and the integrity of the cranks.

-   Pedal bearings are adjusted correctly.  Alter, grease or replace if any roughness 

or looseness is detected in the pedal bearings when the pedals are moved up  
and down, laterally or rotated by hand.

-  The front and rear pedal reflectors are clean and firmly attached.

-   If toe clips are fitted, ensure that they are fastened tightly to the pedals.

49

Pedal Axles

L

L = Left

R

R = Right

Turn Counter-
Clockwise
to tighten

Turn

Clockwise

to tighten

Correct Pedal Attachment

Summary of Contents for Radius









































































Reviews: