Apollo multispot HT3012, User Manual

Page: 16 / 20

User Manual: Multispot-GI-HT3012
V3.00 (08-2013)
14
Output mix presets can be activated by means of CH1 whilst the chosen mix can be
adjusted with CH2. If the value of CH4 is above 50 the unit is set to tact mode. The tact
speed for any fixed output mix chosen on the first channel can be adjusted from zero
(value <50) to 23 cycles per second (value 255).
If DMX value of channel 3 is
equal or higher than 50
the unit works in pattern mode:
CH1 Pattern CH1 Pattern
000-015 Soft fade red-green 136-150 Hard switch green-blue
016-030 Soft fade green-blue 151-165 Hard switch red-blue
031-045 Soft fade red-blue 166-180 Hard switch red-yellow
046-060 Soft fade red-yellow 181-195 Hard switch candy-lime
061-075 Soft fade candy-lime 196-210 Hard switch pink-blue
076-090 Soft fade pink-blue 211-225 Hard switch turquoise-pink
091-105 Soft fade turquoise-pink 226-240 Hard switch red-green-blue
106-120 Soft fade red-green-blue (RGB) 241-255 Hard switch red-yellow-green-
121-135 Hard switch red-green turquoise-blue-pink
DMX Value range Function
CH2
000-255 Level
CH3 050-255 Chase speed
CH4 000-049 Tact off
050-255 Tact (050=slow / 255=max. speed 23 Hz)
The pre-programmed soft fade or hard switching patterns can be chosen by means of
CH1 whilst CH2 is used as a level channel. CH3 allows to set the fade time or pattern
speed from slow (value 50) to very fast (value 255). If channel 4 reaches a DMX value
of 50 or above a tact function will be added to the chases. The tact speed can be
adjusted from slow (value 50) to 23 pulses per second (value 255).
Note: Whether the unit works in static mix mode or pattern mode only depends on the
value of channel 3. So make sure the value of channel 3 is lower than 50 to be in static
mix mode. Otherwise you will be in pattern mode. In this mode the potentiometer (1) is
disabled.
Display on/off
If you wish the display to be lit only when a change in operation is made, the DIP switch
(10) should be in the position off. Now if any of the buttons is not pressed for more than
approximately 25 seconds the display is switched off. As soon as one of the buttons is
pressed again, the display switches on immediately.
Key lock
Pressing the MODE button (5) for longer than 3 seconds locks all the buttons (5-7) and
the potentiometer (1). The display shows “LOC” in alteration to the mode (changing
User Manual: Multispot-GI-HT3012
V3.00 (08-2013)
3
WARNING! Shock hazard. Equipment must be properly grounded.
WARNING! Hot surface. Risk of skin burn or skin irritation.
WARNING! Fire hazard.
WARNING! Laser radiation. Risk of surface damage.
WARNING! LED light emission. Risk of eye injury.
■ Security advice before use
General advice:
1. Read this manual completely before using the product.
2. Keep this manual in your records for future reference.
3. Follow all instruction printed in this manual.
4. Follow all printed security advice on the product itself.
5. Take care of enough distance between this product and sources of
hum and noise like electric motors and transformers.
6. Carry this product with greatest care. Punches, big forces and
heavy vibration may damage this product mechanically.
Protection from eye injury
1. Warning: Depending on the configuration of the device, this device
may reach or exceed the limits of EN62471, risk group 2, and may
hence reach to risk group 3.
2. To avoid eye injury, do not look into the beam from a distance of
less than 8.5 m (27 ft. 11 ins) from the front surface of the fixture
without protective eyewear such as shade-5 welding goggles. At
larger distances, light output is harmless to the naked eye provided
that the eye’s natural aversion response is not affected.
3. Do not view the beam directly with optical instruments such as
magnifiers, telescopes, binoculars or similar optical instruments
that may concentrate the light output.
4. Ensure that during setup and DMX programming, no persons are
inside a 8.50m (27 ft. 11 ins) vicinity of the device’s front surface, to
avoid that they may accidently be exposed to the light beam.