background image

APPLICATIONS 

 

 

The 

Apollo Model 7300ETL Slide Gate Operator 

is designed to handle a slide 

gate up to 30 feet in total length (25 foot gate with 4 foot tail). A professional fence 
or gate dealer is recommended to assure proper installation. 

Apollo Gate 

Operators

 are available only through qualified dealers with an outstanding 

reputation in the fence and gate industry. These dealers will be able to recommend 
the proper equipment for particular applications. 

Apollo Gate Operators 

are 12 Volt 

DC (

Direct Current

) powered. A 12 Volt marine type battery is recommended. There 

are several advantages with 12 Volt DC systems: 
 

• 

Low voltage virtually eliminates risk of electrical shock. 

• 

Battery powered operators provide up to 200 operations in the event of 
power outages. 

• 

The battery may be recharged with a trickle charger or by solar energy  
(eliminating the need for costly trenching to remote entrances).  

 

If a trickle charger is used and a standard electrical outlet is not readily available, a 
licensed electrician will be required for proper electrical hook up. 
 
The following table should be used as a guide for capacity of operation of operators 
only, additional options may reduce the the daily usage. 

Please note that the charge 

capability of solar panels will vary with different geographical locations. All solar 
panels and battery chargers are designed for use with a 12 volt marine type battery. 
 

 
 
 

Model # 

Daily Usage --->  1-10 

1-20 

1-40 

1-60 

1-80 

80+ 

201 

5 watt solar panel 

 

 

 

 

 

210 

10 watt solar panel 

 

 

 

 

 

MSX20 

20 watt solar panel 

(requires 5310 regulator) 

 

 

 

 

 

MSX30 

30 watt solar panel 

(requires 5310 regulator) 

 

 

 

 

 

MSX40 

40 watt solar panel 

(requires 5310 regulator) 

 

 

 

 

 

404 

1.5 amp battery charger 

 

 

 

 

 

405 

10 amp battery charger 

 

 

 

 

 

Summary of Contents for 7300ETL






















Reviews: