Apollo 2009 Owner'S Manual & Technical Handbook Download

Page: 9 / 72

Updated 27/05/08

APOM0508

Apollo Bicycle Company Pty. Ltd. ABN: 60 001 914 469

Road Bicycles.

Road or racing bikes aim to cater for fast travel over long distances on smooth surfaces.
Frames are light weight and rims have a narrower profile, for maximum efficiency and
speed.

Top Tube
Seat
Seat Post
Seat Post Binder Bolt
Seat Stay
Rear Reflector
Rear Brake
Wheel Reflector

Spoke Protector Disc.
Rear Derailleur

Freewheel

Rear Dropout

Handlebar Stem

Head Set

Head Tube

Seat Tube

Down Tube

Front Derailleur

Bottom Bracket Axle

Toe Strap

Toe Clip

Pedal

Crank Arm

Chainwheel

Chainstay

Chain

Tyre Valve

Rim

Tyre

Brake Control Cable

Front Reflector

Brake/Shift Lever

Handlebar

Front Brake

Brake Pad

Wheel Reflector

Front Fork

Front Hub

Spokes

Summary of Contents for 2009









































































Search results

Summary of Contents for 2009

Reviews:

Related manuals for 2009

Brands by name

Popular brands

Apollo 2009, Owner'S Manual & Technical Handbook

Search results

Summary of Contents for 2009

Reviews:

Related manuals for 2009

Brands by name

Popular brands