Instructions for use
What’s in the box?
1 x light unit
1 x battery
1 x mount
1 x retaining ‘o’ ring
1 x charger
Operating
The light needs a full charge before use. It has three
modes and a ‘low’ and ‘high’ setting for each mode.
The modes are as follows:
Time Trialling
Flashes three red LEDs plus green
(high and low settings for daytime use only)
Lone Riding
Three red LEDs flashing
(low setting for night time use, high setting for daytime)
Group Riding
Three red LEDs pulsing
(low setting for night time use, high setting for daytime)
By firmly touching the centre of the lens and holding
your finger on it for one second you will access the
Time Trial mode in its ‘low’ setting. By touching the
lens once more you will activate the ‘high’ setting of
that mode. You can toggle between ‘low’ and ‘high’
by light touches on the lens. By firmly touching the
lens and holding for one second you will switch the
unit off.
From this position, firmly touch and hold the lens for
3.5 seconds, during which time the light will move
from Time Trial mode into Lone Riding mode, with a
frenetic burst of flashing in between to indicate the
mode change. Observe this by looking sideways at
the glow ring. You are now in the ‘low’ setting of the
Lone Riding mode, and by touching the lens once
more you will activate the ‘high’ setting of that mode.
You can toggle between ‘low’ and ‘high’ by light
touches on the lens. By firmly touching the lens and
holding for one second you will switch the unit off.
From this position, touch and hold the lens for 3.5
seconds, during which time the light will move from
Lone Riding mode into Group Riding mode, with a
frenetic burst of flashing in between to indicate the
mode change. Observe this by looking sideways at
the glow ring. You are now in the ‘low’ setting of the
Group Riding mode, and by touching the lens once
more you will activate the ‘high’ setting of that mode.
You can toggle between ‘low’ and ‘high’ by light
touches on the lens. By firmly touching the lens and
holding for one second you will switch the unit off.
To get back to Time Trialling mode, firmly touch and
hold the lens for 3.5 seconds, and after the frenetic
burst of flashing the light will be in Time Trial mode.
You are now back to the beginning and can cycle
through the modes as described above.
NB. The light will always come on in the ‘low’ setting
of the mode in which it was last used.
Charging the battery
The Scorpion QR comes with a plug-in charger. It will
take 3–4
hours to charge completely from when it is
fully discharged. To help extend the long term life
of the Li-ion battery, charge the light when it is
almost depleted.
Disconnect the light from the battery by unscrewing
the slotted collar and firmly pulling the lens section
and the battery apart. (The action is a direct pull and
not a wobble side-to-side pull, which would weaken
the pins.) Plug the FOUR4TH battery charger into
the mains and the small LED on the front will glow
green. Attach the cable to the battery by aligning the
notch on the connector with the corresponding slot
on the battery. Gently rotate the cable until you feel
alignment, then push home – you will hear a click.
The LED on the charger will now show red. When a
full charge is attained (after 3–4 hours) the LED will
show green. Disconnect the battery from the charger
and unplug the charger from the mains.
Reattaching the battery
Reattach the battery to the Scorpion QR by aligning
the notches on the lens section with the slot on the
battery. When you feel alignment, push home – you
will hear a click. Tighten the collar.
Note: When the unit is correctly attached to the
battery there is a 0.2mm gap between the silver collar
and the black body. This is a deliberate design feature
created by the rubber ‘o’ ring inside the body. It acts
as a water seal and also prevents the two parts of the
light becoming unintentionally unscrewed. If you notice
this gap has diminished, then it is time to replace the
seal. Replacements are available on our website.
SCORPION QR
