background image

PNEG-1608

 Pathogen Barrier Filter Ducts

23

4. Warranty

Limited Warranty - Protein Products

The GSI Group, LLC. (“GSI”) warrants products which it manufactures, to be free of defects in materials and workmanship 
under normal usage and conditions for a period of 12 months from the date of purchase (or, if shipped by vessel, 14 months 
from the date of arrival at the port of discharge). If, in GSI’s sole judgment, a product is found to have a defect in materials 
and/or workmanship, GSI will, at its own option and expense, repair or replace the product or refund the purchase price. 
This Limited Warranty is subject to extension and other terms as set forth below.

Warranty Enhancements:

The warranty period for the following products is enhanced as shown below and is in lieu of (and not in addition to) the 
above stated warranty period.

Conditions and Limitations:

THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE LIMITED WARRANTY DESCRIPTION SET FORTH 
HEREIN; SPECIFICALLY, GSI DISCLAIMS ANY AND ALL OTHER WARRANTIES OF ANY KIND, EXPRESS OR 
IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A 
PARTICULAR PURPOSE OR USE IN CONNECTION WITH: (I) ANY PRODUCT MANUFACTURED OR SOLD BY 
GSI, OR (II) ANY ADVICE, INSTRUCTION, RECOMMENDATION OR SUGGESTION PROVIDED BY AN AGENT, 
REPRESENTATIVE OR EMPLOYEE OF GSI REGARDING OR RELATED TO THE CONFIGURATION, INSTALLATION, 
LAYOUT, SUITABILITY FOR A PARTICULAR PURPOSE, OR DESIGN OF SUCH PRODUCTS.

The sole and exclusive remedy for any claimant is set forth in this Limited Warranty and shall not exceed the amount paid 
for the product purchased. This Warranty only covers the value of the warranted parts and equipment, and does not cover 
labor charges for removing or installing defective parts, shipping charges with respect to such parts, any applicable sales 
or other taxes, or any other charges or expenses not specified in this Warranty. GSI shall not be liable for any other direct, 
indirect, incidental or consequential damages, including, without limitation, loss of anticipated profits or benefits. Expenses 
incurred by or on behalf of a claimant without prior written authorization from the GSI warranty department shall not be 
reimbursed. This warranty is not transferable and applies only to the original end user. GSI shall have no obligation 
or responsibility for any representations or warranties made by or on behalf of any dealer, agent or distributor. Prior to 
installation, the end user bears all responsibility to comply with federal, state and local codes which apply to the location 
and installation of the products.

This Limited Warranty extends solely to products sold by GSI and does not cover any parts, components or materials used 
in conjunction with the product, that are not sold by GSI. GSI assumes no responsibility for claims resulting from 
construction defects, unauthorized modifications, corrosion or other cosmetic issues caused by storage, application or 
environmental conditions. Modifications to products not specifically delineated in the manual accompanying the product at 
initial sale will void all warranties. This Limited Warranty shall not extend to products or parts which have been damaged 
by negligent use, misuse, alteration, accident or which have been improperly/inadequately maintained.

Service Parts:

GSI warrants, subject to all other conditions described in this Warranty, Service Parts which it manufactures for a period 
of 12 months from the date of purchase, unless specified in Enhancements above. Parts not manufactured by GSI will carry 
the Manufacturer’s Warranty.

Product

Warranty Period

AP

®

 Fans

Performer Series Direct Drive Fan Motor

3 Years

* Warranty prorated from material list price:

0 to 3 years - no material cost to end user
3 to 5 years - end user pays 25%

5 to 7 years - end user pays 50%

7 to 10 years - end user pays 75%

** Warranty prorated from material list price:

0 to 3 years - no material cost to end user
3 to 5 years - end user pays 75%

AP

®

 and Cumberland

®

Flex-Flo/Pan Feeding System Motors

2 Years

Electronic Controls

All Protein controls manufactured by GSI

24 Months from date
code on part

Cumberland

®

Feeding and Watering
Systems

Feeder System Pan Assemblies

5 Years, Prorated **

Feed Tubes (1.75" and 2.00")

10 Years, Prorated **

Centerless Augers

10 Years, Prorated **

Watering Nipples

10 Years, Prorated **

(Protein Limited Warranty_REV01_06 November 2018)

Summary of Contents for PNEG-1608

























Reviews: