background image

TABLE OF CONTENTS

 

CARE & SAFETY PRECAUTIONS ………………………….. 3 

PRODUCT DESCRIPTION …………………………………… 4 

FUNCTIONS & FEATURES …………………………………… 4 

PACKAGE INCLUSION ……………………………………..  5 

SPECIFICATIONS ……………………………………………. 5 

OPERATING PROCEDURES ……………………………...  6­11 

BASIC TROUBLESHOOTING GUIDE …………………….... 12

 

11 

OPERATING PROCEDURES 

6. 

After the process is finish the display will show

 “End”, 

press the 

increase button to save the profile and exit to profile adjustment 

mode. 

7. 

To  exit  before the  process  is  finished  press  the  increase  button 

while the profile is running. The system would exit and return to 

profile adjustment mode.

 

Note:

There  is  a  built  in  protection  feature  to  automatically  limit  the 

temperature  rising  slope  to  no  more  than  3  degrees  per  second. 

Therefore based on your set time, the maximum temperature may not 

reach 250C.

 

Profile analysis: 

SEG1          SEG2         SEG3         SEG4         SEG5          SEG6 

050t           060t           080t          050t          040t             60t 

100C          150C          180C         190C         195C           100C 

Segment  one  is set  to  50  seconds  to  reach  100C. Which  means  after 

50seconds  at  the  end  of  segment  one  the  temperature  should  reach 

100C.  Then  Segment  two  is  set  to  60  seconds  to  reach  150C,  which 

means  by  the  end  of  60  seconds  the  set  temperature  should  reach 

150C, so on and so forth. 

To check the slope from segment Two : 

 

150C ­ 100C =30C 

 

Time to reach 150C is set to 60seconds. 

 

Therefore  the  slope  is  50/60=  0.833  degrees  per  second 

increase. 

To determine the slope if it is declining as seen in segment six: 

 

195C ­ 100C =95C 

 

Time to reach 100C is set to 60seconds. 

 

Therefore the slope is 95/60= 1.58 degrees per second decline.

Summary of Contents for INT883







Reviews: