Aopos AS230+ User Manual Download | Manualshive

Page: 66 / 70

background image

62

Assembling the stand

1.

See the figure above, tighten the screws.

2.

Bend the neck to the desired position for scanning.

3.

Screw mounting: Screw one #10 wood screw into each screw-mount-hole until the base of the stand
is secured.

4.

Tape mounting: ①Peel the paper liner off one side of each piece of tape and place the sticky
surface over each of the three rectangular tape holders. ②Peel the paper liner off the exposed
sides of each piece of tape and press the stand on a flat surface until it is secure.

«
...
64
65
66
67
68
...
»

Summary of Contents for AS230+







































































Reviews:

No comments

Related manuals for AS230+

Brand: Banner Pages: 4

ABR 3000 series

Brand: Banner Pages: 8

Brand: Element Pages: 120

Brand: AEG Pages: 17

Brand: Sealey Pages: 4

Brand: ViewSonic Pages: 128

Brand: Viking Pages: 4

Fastmark M4 Series

Brand: AMT Datasouth Pages: 2

Fastmark M7 Series

Brand: AMT Datasouth Pages: 19

Fastmark M1/203dpi

Brand: AMT Datasouth Pages: 32

Brand: Gems Pages: 107

Brand: Y-E Data Pages: 27

Brand: Seuic Pages: 11

Brand: Elatec Pages: 50

Brand: 2connect Pages: 88

MMC/SD Card Reader

Brand: LEI Extras Pages: 6

Brand: Saveo Scan Pages: 3

Brand: Fametech Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands