background image

WARNING

Use stainless steel flexible hoses or copper 

tubes of 1/2” on the inlet and outlet. 
DO NOT USE PVC, CPVC or plastic supply 
line directly to the heater.

This appliance is forbidden to be switched 

on if you think it may be frozen, as this could 
result in serious damage to the unit. Wait until 
you are sure that it has completely thawed out 
before you switch it on.

This appliance is not intended for use by 

persons (include children) with reduced physical 
sensory or mental capabilities, or lack of 
experience and knowledge, unless under careful 
supervision. Children should be supervised to 
ensure that they do not play with the appliance.

Safety and energy conservation are factors to 

be considered when selecting the water 
temperature setting of water heater’s thermostat. 
Water temperatures above the 125°F (52°C) can 
cause severe burns from scalding.

DO NOT store or use gasoline or other 

flammable vapors and liquids in the vicinity of 
this or any other appliance. Keep rags and other 
combustibles away. 

If the water heater has been subjected to flood, 

fire, or physical damage, turn off power and water 
to the water heater. Do not operate the water 
heater again until it has been thoroughly checked 
by qualified service personnel. 

When using electrical appliances, basic 

safety precautions should always be 

followed including the following:

The installation must be in compliance with 

the National Electrical Code

, your local 

electrical and plumbing codes. 

This appliance must be 

GROUNDED. 

CONNECTED ONLY TO A CIRCUIT THAT IS 
PROTECTED BY A RECOGNIZED GROUND-
FAULT CIRCUIT INTERRUPTER(GFCI).

We highly recommend that you employ the 

services of a professional to assist you with 
this installation if you are not familiar with 
basic plumbing and electricity. Under no 
circumstances should you attempt to install, 
repair or disassemble the water heater 
without first disconnecting the electricity.

Install or locate this water heater only in 

accordance with the provided installation 
instructions. 

Use this water heater only for its intended 

use as described in this manual.

This appliance MUST be permanently 

connected to the fixed circuit breaker and it 
must be installed vertically. DO NOT install 
near tinder or a strong magnetic field.

SWITCH OFF the breaker before removing 

the cover for servicing.

If there is damage to the wire, you must 

contact qualified electrician to replace it with 
dedicated wire from our authorized dealers.

PG.1

SAFETY PRECAUTIONS

Summary of Contents for ENVO WH-AZ011-M2

















Reviews: