background image

SAFETY  PRECAUTIONS 

Please carefully read lhe safety precaulions before inslallalion. This is importanl and must be 

observed. 

LL 

DANGER

Only connect lo a Ground-Faull Circuit-lnlerrupter(GFCI) protected grounded socket. 

Do not remove the ground pin or use a ground adapter. 

LL 

WARNING

•Any modification to your ENVO  Electric Bidet

Seat  will lead to warranty failure.  If  cables, 

plugs or other components need to be repaired 
or replaced, they need to be handled  by 

qualified electricians. 

•Any 

replacement shall be provided by 

ANZZI.

The use of a third-party replacement will

invalidate the warranty. 

•Cut off the 

power 

supply before maintenance.

•Ensure that the bathroom is well ventilated to

avoid moisture accumulation. Installing the
smart toilet in a humid place may cause
electrical failure of the product.

• In any case, the socket shall be installed at a

position greater than 19-11 /16"(500mm) from
the bathtub.

• Do not touch the power socket with wet

hands, 

Otherwise it may cause electric

shock.

• Do not pour water, hot water or detergent

onto the top of the  Electric bidet seat, power 

supply or plug. 

•Make 

sure the  Electric bidet seat  is 

away 

from flames or  combustibles.

•Do not put your fingers or anything at the

oullel of lhe heater, 

Otherwise it may cause

burns or electric shock.

•Do not excessively pull or bend the cable.  If

there is any damage to the cable or plug, cut off

the power supply. Use the cable  provided by

ANZZI 

for replacement.

•Do not bend or squeeze the water inlet hose

hard, 

Otherwise it may lead to water leakage

•When power failure occurs during  cleaning

and the nozzle is not reset,  do not push it 

back by hand. The nozzle will reset itself 

after the power supply is restored. 

• If your ENVO  Electric Bidet Seat has the

following problems, please stop using it. Turn 
off power  supply and supply stop.

--Pipe, hose or product leaks.
--Product breakage.
--The product has abnormal sound or

peculiar smell. 

--Smoke from the product. 

• Do not use while bathing .
Do not place or store product where it can

fall or be pulled into a tub or sink.

Do not place in or drop into water or other

liquid.

Do not reach for a product that has fallen into

water. Unplug immediately.

Strong magnets inside,  if the body is equipped

with a pacemaker and other auxiliary medical

equipment, please do not use.

PG.1 

Summary of Contents for ENVO TL-AZEB101B

























Reviews: