background image

Need assistance? Call our technical support line at 

305-614-4070

 or visit us at 

www.ANZZI.com

PRODUCT REGISTRATION*

IMPORTANT: YOUR WARRANTY WILL NOT BE RECOGNIZED UNLESS THIS CARD  IS 
FULLY COMPLETED AND RETURNED OR ONLINE REGISTRATION IS COMPLETED.

1. 

Register online at 

www.swcorp.com/register

You will be asked to fill out the same 

information you would in the registration card. Registering online is fast, secure and 
ensures we receive your information. 

2.  

Complete, cut-out and mail the registration card below.

 

By returning this registration 

card we confirm the date of purchase for your new product. This confirmation will allow 
us to process any warranty claims.

Mail the card to: 5701 NW 35 Avenue, Miami, FL 33142

Product Registration Card

Name .....................................................................................   Address ...........................................................................................................................

City ...............................................  State ...........................  Zip ..............................

Phone ...........................................  Email ....................................................................

Date of Purchase...........................

Installer’s Name .....................................................................   Phone ................................................................................

I have read the Owner’s Manual carefully and understand and agree that any installation, operation or maintenance of the product must be done
strictly in accordance with instructions and guidelines contained in the owner’s manual and installation guide.

Signature

____________________________________________________________

Date

 ______________________________________________

CUT ALONG

DOTTED LINE.

Summary of Contents for Anzzi SB-AZ009W















Reviews: