Anybus cB-RBS421 Product Manual Download Page 11

Additional Information 

Guidelines for Efficient and Safe Use 

Read this information before using your gateway. 
For any exceptions, due to national requirements or limitations, when using your 
gateway, please visit 

www.bluetooth.com

Note: Changes or modifications to the product not expressly approved by HMS 
will void the user's authority to operate the equipment.

 

Product Care 

 

Do not expose your product to liquid or moisture. 

 

Do not expose you product to extreme hot or cold temperature (see Technical 
Specification for further information) 

 

Do not expose your product to lit candles, cigarettes, cigars, open flames, etc. 

 

Do not drop, throw or try to bend your product since rough treatment could 
damage your product. 

 

Do not attempt to disassemble your product. Doing so will void warranty. The 
product does not contain consumer serviceable or replaceable components. 
Service should only be performed by HMS. 

 

Do not paint your product as the paint could prevent normal use. 

 

If you will not be using your product for a while, store it in a place that is dry, 
free from damp, dust and extreme heat and cold. 

 

The clearance and creepage distances required by the end product must be 
withheld when the module is installed. 

 

The cooling of the end product shall not negatively be influenced by the 
installation of the module when the module is installed. 

Radio Frequency Exposure 

The gateway contains a small radio transmitter and receiver. During communication 
with other Bluetooth products the gateway receives and transmits radio frequency 
(RF) electromagnetic fields (microwaves) in the frequency range 2400 to 2500 MHz. 
The output power of the radio transmitter is very low. 
When using the gateway, you will be exposed to some of the transmitted RF energy. 
This exposure is well below the prescribed limits in all national and international RF 
safety standards and regulations. 

Electronic Equipment 

Most modern electronic equipment, for example, in hospitals and cars, is shielded 
from RF energy. However, certain electronic equipment is not. Therefore: 

Note

: This equipment emits RF energy in the ISM (Industrial, Scientific, Medical) 

band. Please insure that all medical devices used in proximity to this device meet 
appropriate susceptibility specifications for this type of RF energy. 

 

Summary of Contents for cB-RBS421















Reviews: