Anviz bl100, Installation Manual

Page: 6 / 7

Ⅲ
. Enroll an Ordinary User
Ø
Enroll a Fingerprint Ordinary User
1.
Press key to start the lock and enter the Verify State.
2. There have two methods to enter the Management Mode:
①
Press and hold the key until you hear 1 long
beep, enter the 5 digits MPC, and then press key to enter the Management Mode.
②
Verify the registered
administrator's password and fingerprint to enter the Management Mode.
3. Press "1" to enter the Enroll Ordinary User's Fingerprint Mode.
4.
Input 3 digits User ID, then press key to confirm.
J
Note : The ordinary users' ID must between "001" and "994".
5. Press finger in the scanner area properly, and repeat it for three times, until you hear one long beep and LED
flashes Green, namely enrollment successful.
Ø
Enroll a Password Ordinary User
1. Press key to start the lock and enter the Verify State. Enter the Management Mode; see the methods on
how to enter the management mode in the
Enroll a Fingerprint Ordinary Users
.
2. Press "2" on the lock to enter the Enroll Ordinary User's Password Mode.
3. Input 3 digits User ID, and press key to confirm.
J
Note : The ordinary users' ID must between "001" and "994".
4. Input 4 digits user password, press key to confirm. Enter the 4 digit user password once again and press
key to confirm until you hear one long beep and LED flashes Green. The Keypad area lights blue LED and
the key lights green LED, namely register successful.
Ⅳ
. User Verification
Ø
The Fingerprint Verification
1. Press key to start the lock and enter the Verify State. The Fingerprint Collector is in active state.
2. Press finger in the fingerprint scanner area properly, until you hear one long beep, namely collect successful.
(1) If verify successful, the buzzer will give a long beep and unlock automatic, the green LED and the Fingerprint
Collector
will put out, the Green LED at key will light for 3 seconds, at this moment your can press
key to lock.
3. Press "5" key on the lock and enter the new 5 digits MPC , then press the key to confirm. Enter the new
MPC once again then press the key to confirm. Once you hear 1 long beep and the key flashes green,
namely you have successfully changed the MPC code.
.
Ⅱ
Enroll an Administrator
1. Press key to start lock, and then enter the Verify State.
2. Press and hold the key until you hear 1 long beep, enter the 5 digits MPC, and then press key to
enter the Management Mode.
3. Press "9" on the lock to enter the Enroll Administrator Mode.
Ø
Enroll a Fingerprint Administrator User
J
Note
: 1­3 steps are same as above. Here is no longer to restatement.
4. After enter the Enroll Administrator Mode, press number keys of the lock to enter 3 digits user ID, and then press
key to confirm.
J
Note : The administrator User's ID must between "995" and "999".
5. Press finger in the scanner area properly, and repeat it for three times, until you hear one long beep and LED
flashes Green.
Ø
Enroll a Password Administrator User
J
Note : 1­3 steps are same as above. Here is no longer to restatement.
4. After enter the Enroll Administrator Mode, enter 3 digits user ID, press key to confirm.
5. Press 4 digits user password and press key to confirm, and then enter the 4 digits user password once again
and press key to confirm, until you hear one long beep and LED Flashes Green (If it fails to register ­ it will
give 2 short beeps and LED will flash red).
J
Note
:
①
If Pass code does not match or input the wrong digit password, then you have two times to try again.
If your input the wrong at the third time, then it will prompt fail registration. In this case you will need to follow step
1 to operate again.
②
If successful, it will automatically exit the Enroll Administrator Mode.
③
Press and hold "0"
key, can exit anytime.
④
If you want to enroll more administrator user, and then repeat the step 1­5.
­ 11 ­
­ 12 ­