Antunes JS-1000 International Owner’S Manual Download Page 18

Limited Warranty

Equipment manufactured by Antunes has been constructed of the finest materials available and manufactured to high quality stan

-

dards.  These units are warranted to be free from electrical and mechanical defects for a period of one (1) year from date of pur-

chase under normal use and service, and when installed in accordance with manufacturer’s recommendations.  To insure continued 

operation of the units, follow the maintenance procedures outlined in the Owner’s Manual.  During the first 12 months, electrome

-

chanical parts, non-overtime labor, and travel expenses up to 2 hours (100 miles/160 km), round trip from the nearest Authorized 

Service Center are covered.

1. 

This warranty does not cover cost of installation, defects caused by improper storage or handling prior to placing of the Equip-

ment.  This warranty does not cover overtime charges or work done by unauthorized service agencies or personnel.  This 

warranty does not cover normal maintenance, calibration, or regular adjustments as specified in operating and maintenance in

-

structions of this manual, and/or labor involved in moving adjacent objects to gain access to the equipment.  This warranty does 

not cover consumable/wear items. This warranty does not cover damage to the Load Cell or Load Cell Assembly due to abuse, 

misuse, dropping of unit/shock loads or exceeding maximum weight capacity (4 lbs).  This warranty does not cover water con-

tamination problems such as foreign material in water lines or inside solenoid valves.  It does not cover water pressure problems 

or failures resulting from improper/incorrect voltage supply.   This warranty does not cover Travel Time & Mileage in excess of 2 

hours (100 miles/160 km) round trip from the nearest authorized service agency. 

2. 

Antunes reserves the right to make changes in design or add any improvements on any product.  The right is always reserved 

to modify equipment because of factors beyond our control and government regulations.  Changes to update equipment do not 

constitute a warranty charge.

3. 

If shipment is damaged in transit, the purchaser should make a claim directly upon the carrier.  Careful inspection should be 

made of the shipment as soon as it arrives and visible damage should be noted upon the carrier’s receipt.  Damage should be 

reported to the carrier.  This damage is not covered under this warranty.

4. 

Warranty charges do not include freight or foreign, excise, municipal or other sales or use taxes.  All such freight and taxes are 

the responsibility of the purchaser.  

5. 

This warranty is exclusive and is in lieu of all other warranties, expressed or implied, including any implied warranty or mer-

chantability or fitness for a particular purpose, each of which is hereby expressly disclaimed.  The remedies described above 

are exclusive and in no event shall Antunes be liable for special consequential or incidental damages for the breach or delay in 

performance of this warranty.

+1 (630) 784-1000

+1 (800) 253-2991

+1 (630) 784-1650

+86-512-6841-3907

+86-512-6841-3637

Summary of Contents for JS-1000



















Reviews: