manualshive.com logo in svg

Antunes 9100618, Owner'S Manual

Share
Download
Antunes 9100618 Owner'S Manual Download Page 6

CHEESE MELTER

6

P/N 1010983 Rev. F 05/19

®

SPECIFICATIONS

Electrical Ratings

WARNING

ELECTRICAL SHOCK HAZARD.

FAILURE TO FOLLOW THE INSTRUCTIONS IN 

THIS MANUAL COULD RESULT IN SERIOUS  

INJURY OR DEATH.

•  Electrical ground is required on this appliance.

•  Do NOT modify the power supply cord plug.  If 

it does not fit the outlet, have a proper outlet 

installed by a qualified electrician.

•  Do NOT use an extension cord with this appliance.

•  Check with a qualified electrician if you are unsure 

if the appliance is properly grounded.

CAUTION

All electrical connections must be in accordance 

with local electrical codes and any other  

applicable codes.

Electrical Cord & Plug Configurations

Model & 

Mfg. No.

Description

Configuration

RS-250 

9100618

NEMA 6-20P,  

20 Amp.,  

250 VAC,  

Right Angle Plug 

CAUTION

HOT SURFACES

CUIDADO CALIENTE

MISE EN GARDE-CHAUD

HEISSE OBERFLÄCHE

 1

2

12.5”

(318 mm)

15.25”

(387 mm)

20”

(508 mm)

Dimensions

Model &  

Mfg. No.

Voltage

Watts

Amps

Hertz

RS-250 

9100618

208

3300

15.9

50/60

Summary of Contents for 9100618





























Reviews:

No comments

Brands by name

Popular brands

Load more brands