ArcPower 192 Outdoor US
16
rAd.t.
---
Unlink time.
Use this menu to set time after that the linked fixture will be unliked from the transmitter, if
the transmitter does not transmit DMX signal.
OFF
--- Fixture is permanently linked to the transmitter.
4day-25.5
--- Time from 4 days to 0.1-25.5 hrs. Default value is 1 hr.
M.F.ti.
---
Max. Fade time.
Select this menu item to set a desired max. fade time (0-25.5 sec.). This adjusted fade
time influences fade of RGB and dimmer during DMX operation:
If time between two receiving DMX values is > than fade time set in the item M.F.ti., the entire adjusted fade time
will be used.
If time between two receiving DMX values is < than fade time set in the item M.F.ti., the adjusted fade time will be
reduced to fill entire time between the two receiving DMX values.
e.g. M.F.ti.=2sec. and fixture has received Red=0 DMX, after 5 seconds will receive Red=255 DMX. It means, that
red will go to full intensity during 2 seconds.
M.F.ti.=8 sec. and fixture has received Red=0 DMX, after 5 seconds will receive Red=255 DMX. It means, that red
will go to full intensity during 5 seconds. (Max, fade time is reduced from 8 sec. to 5 sec.).
tEM.U.
---
Temperature Unit.
Use this menu in order to display the fixture temperatures in desired units: °C or °F.
bALA --- White colour balance
Use this menu item to enable (On) or disable (Off) the white balance which is set in
the “White colour balance“ menu below. I f this function is set off, the will use maximum value (255) of saturation
for red, green and blue colour. This function has to be set on before adjusting a white balance. The white colour
balance can be switched on/off for each LED output independent.
C.bAL.
---
White colour balance setting.
The menu gives access to the setting of the white balance.
The white colour balance can be set for each LED output independent.
To set the white colour balance.
1.
Use a DMX controller or the “ Man.C.“ menu to set all LEDs on max. saturation.
2.
Use the UP/DOWN buttons to find the “ Pers.“ menu.
3.
Press the ENTER button.
4.
Use the UP/DOWN buttons to select the “C.bAL“menu.
5.
Press the ENTER button and the “rEd1“ item will appear on the display.
6.
Press the ENTER button and use the UP/DOWN buttons to set new max. value for the red LEDs.
7.
Press the ENTER button to confirm the choice.
8.
Use the UP/DOWN buttons to select next colour, the “GrE1“.
9.
Repeat steps 6-7 for this channel.
10.
Use the UP/DOWN buttons to select the last colour, the „bLu1“ and repeat steps 6-7 for this colour.
11.
Repeat this procedure for all LED outputs
12.
Use the UP/DOWN buttons to find the item “ Stor.“ and press the ENTER button to save adjusted values.
LoAd
---
Load of LED outputs
. The menu allows to choose desired current (350mA or 700mA) for each LED output.
Warning: Set the “Load“ item before connecting the LED modules to the driver.
Never connect 1Watt LEDs to the 700mA output otherwise these LEDs vill be destroyed.
In.Po.
---
Init effect positions.
Use this function to set all effects to the desired positions to which they will move
after switching the fixture on (if DMX is not being received).
dF.SE.
---
Default Settings .
The menu item sets all fixture parameters to the default (factory) values.
6.4 Manual mode
Use this menu for control the fixture without connected DMX console.
Summary of Contents for ArcPower Outdoor 192 US
Page 1: ...Version 1 6...
