Animo OptiVend 1, Manual, Page: 8 / 29

58
08/2011 Rev. 7.4
M o d e l 2 0 0 9
08/2011 Rev. 7.4
59
M o d e l 2 0 0 9
3. INSTALLATION
This device should only be placed and connected by an authorised service engineer. The following
must be taken into account:
• Only suitable for indoor use
• Unsuitable for use in damp areas
• Unsuitable in areas with a risk of explosion
3.1 Unpacking
In order to prevent any damage to your new purchase, the device is carefully packaged.
You should carefully remove the packaging without using any sharp objects. Check whether the device
is complete. In order to protect the device, the stainless steel sections are partly wrapped in protective
foil. This foil should be removed during installation.
The device is supplied with the following accessories:
Number Number
Measuring cup 0,25L 1 Recipe strips (set) 1
Drip tray + grid 1 0.5 m Drain hose (Drip tray) 1
Coffee fur remover (sachet) 1 1.5 m Connection hose 1
Brush 1 User manual 1
Door keys 2 Service manual 1
If some parts are missing or damaged, please contact your dealer.
WARNING
Some water will always remain in the heating system. Therefore never place the device in an area
where the temperature can drop below freezing.
3.2 Placement preparation
• Place the device at work top height on a rm, at surface so that it can support the weight of the
(
lled) device.
• Make sure that the device is level and cannot cause damage in case of any leakage.
• Make sure that the ventilation openings at the back of the device are not obstructed.
• The water supply and electricity plug should be no further than half a meter away from the position
of the device.
• These installation technical preparations must be out sourced by the user and should be carried out
by an authorised tter according to the general and local regulations.
• Only the service engineer can connect the device to the prepared connection points.
3.3 Water connection
Connect the device to a well accessible tap with air
valve, which can be turned off quickly in case of prob-
lems. The minimal water pressure must not fall below 2
bar (at 6 l/min ow pressure).
If necessary, the OptiVend can be connected to hot
water. We explicitly advise you to use a special hot
water connection tube ( g. 2).
Hot water connection tube Art. No. 08175.
3.3.1 Water treatment (fi g. 3)
We explicitly advise you to use a water softener and/
or water lter if the tap water has been chlorinated or is
too hard. This increases the quality of the drink and will
ensure that you do not have to descale the device too
often.
Filter system Brita Purity C150 Art.No. 99671
Filter system Brita Purity C300 Art.No. 99672
Filter system Brita Purity C500 Art.No. 1000293
incl. cartridge and connection tube set
Cartridge Brita Purity C150 Art.No. 07982
Cartridge Brita Purity C350 Art.No. 07983
Cartridge Brita Purity C500 Art.No. 1000293
3.3.2 Stand-alone pump set (fi g. 4)
If no xed water connection point is present near the
machine, a stand-alone pump set can be supplied as
an option.
Water pump stand-alone Art. No. 93500
Water tank 18 litre stand-alone Art. No. 01013
3.3.3 Base cabinets (fi g. 5)
A number of base cabinets are available as an option
for the OptiVend machines.
Base cabinet Art. No. 65055
Prepared for building in a stand-alone pump set and
for fitting a water filter at the back.
Work top small Art. No. 03315
Work top large Art. No. 03316
Base cabinet with cooling unit Art. No. 65015
Prepared for building in a cooling unit (OptiVend Hot
& Cold) and for fitting a water filter at the back.
Fig. 2
Fig. 3
Fig. 4
Fig. 5
60°C