background image

Controls 

 
 
 
 
Heating zone controller E8 

20 

 

Heating zone controller E8 

The R600 can be extended with an E8 
controller for extended control of two 
heating zones and sanitary hot water 
operation. The E8 combines weather 
compensated operation with control of 
two heating zones and the control of a 
secundary hot water circulation pump. 

6a 

7a 

6b 7b 

6c 7c 

1  KM628 (integrated in boiler) 
2  Outside temperature sensor, to be connected at terminals 105-106 
3  E8 (integrated in boiler) 
4  Primary sanitary hot water pump control, to be connected at terminals 19-20-21 
5  Sanitary hot water sensor, to be connected at terminals 114-115 (Remove jumper from terminals 113-114!) 
6 Heating 

zone 

 

a  Temperature sensor, to be connected at terminals 125-126 

 

b  Pump, to be connected at terminals 50-51-53 

 

c  Mixing valve, to be connected at terminals 55-56-57 

7 Heating 

zone 

 

a  Temperature sensor, to be connected at terminals 127-128 

 

b  Pump, to be connected at terminals 51-52-53 

 

c  Mixing valve, to be connected at terminals 59-60-61 

8  Sanitary hot water circulation pump, to be connected at terminals 63-64-65 

 

 Further details about the electrical connections can be found on the wiring diagram. 

In case of heating systems with more 
than two heating zones, an additonal kit 
with E8 in a wall hung box is available. 
These kits can be used in a modular 
way up to a maximum of 15 heating 
zones. 

For room temperature optimisation of 
each heating zone, an additional roo-
munit BM8 can be connected via bus 
connection. The values for the specific 
heating zone can then be displayed 
and changed on the room unit. 

Summary of Contents for SH60

















































Reviews: