andrews MAXXflo EVO CWH 90/302 Installation And Maintenance Manual Download Page 67

Page: 67 / 84

Maintenance

MAXXflo EVO

6.2.14 CIRCuLATION PuMP Q1

• Close the shut off valve before and after the pump.

• Use the drain points between the shut off valves to remove water from the pump

• Remove the PWM and power connectors, using a small flat blade screwdriver to lift the white tab before

pulling each connector free.

• Undo the unions at the top and bottom of the pump body and remove pump.

• Fit the new pump seals

• Replacement is the reverse

• Refill and bleed of air

• Operate the pump by pulling the electrical connector off the heat exchanger front flow sensor (B2)

• When all sound of air has stopped, reconnect B2 sensor and press the reset for around one second

Pump Union

B2 Sensor

Summary of Contents for MAXXflo EVO CWH 90/302





















































































Search results

Summary of Contents for MAXXflo EVO CWH 90/302

Reviews:

Related manuals for MAXXflo EVO CWH 90/302

Brands by name

Popular brands

andrews MAXXflo EVO CWH 90/302, Installation And Maintenance Manual

Search results

Summary of Contents for MAXXflo EVO CWH 90/302

Reviews:

Related manuals for MAXXflo EVO CWH 90/302

Brands by name

Popular brands