andrews ECOflo EC230/600 Installation Manual, Operation And Maintenance Manual Download

Page: 20 / 52

SECTION 3 •

INSTALLATION

VERTICAL FLUE KIT/FITTINGS PACK

– 380 LITRE MODELS

AWH PART No: B292

SUPPLIED COMPONENTS

Part Description

Part Number

Exhaust Outlet Tee c/w Condense Outlet (82500)

E860

100mm to Concentric Exhaust Pipe (75413)

E865

Air intake Tee Piece Connector (82501)

E862

Condense Syphon (87436)

E863

Horizontal Flue Terminal, 100/150mm (87990)

E236

90° Elbow c/w clamp, 100/150 (87890)

E205

Gas Cock – ¾”BSP

C498

Drain Valve – ¾”BSP

C381

Drain Valve Socket – ¾”BSP

C103

Installation, Operation and Maintenance Manual

E864

VERTICAL FLUE KIT/FITTINGS PACK

– 380 LITRE MODELS

AWH PART No: B294

SUPPLIED COMPONENTS

Part Description

Part Number

Exhaust Outlet Tee c/w Condense Outlet (82500)

E860

100mm to Concentric Exhaust Pipe (75413)

E865

Air intake Tee Piece Connector (82501)

E862

Condense Syphon (87436)

E863

Vertical Flue Terminal, 100/150mm (87969)

E866

Gas Cock – ¾”BSP

C498

Drain Valve – ¾”BSP

C381

Drain Valve Socket – ¾”BSP

C103

Installation, Operation and Maintenance Manual

E864

FLUE SYSTEMS

Optional Components for 100/150mm dia (concentric) Flue

Quantity

Flue Length

Part Description

Part Number

1000mm (40in)

Flue pipe with clamp

E202

1000mm (40in)

Cutable flue pipe with clamp

E203

500mm (20in)

Flue pipe with clamp

E204

90° Elbow

E205

45° Elbow

E206

Flat roof flashing for vertical flue terminal with adjustable cap

E207

Roof flashing for pitched roof to suit 150mm (6in) dia flue size

E208

Wall clamp 150mm (6in) dia.

E209

Flue condense trap

E210

Syphon

E211

Condensate trap pipe kit to syphon

E261

Model

EC230/600

EC230/700

EC230/960

EC380/740

EC380/980

EC380/1220

EC380/1400

Flue size (concentric)

100/150

Max flue run – room sealed (a) m

Reduce flue length by 1.2m for 90° bend, 0.7m for 45° bend and 1.5m for a condensate trap.

The ventilation requirements for room sealed flue systems are given on pages 29 and 30.

ECOflo_E864_manual_SEPT2012 16/10/12 11:24 Page 20

Summary of Contents for ECOflo EC230/600





















































Search results

Summary of Contents for ECOflo EC230/600

Reviews:

Related manuals for ECOflo EC230/600

Brands by name

Popular brands

andrews ECOflo EC230/600, Installation Manual, Operation And Maintenance Manual

Search results

Summary of Contents for ECOflo EC230/600

Reviews:

Related manuals for ECOflo EC230/600

Brands by name

Popular brands