manualshive.com logo in svg

Anchor Perfectshade, Assembly Instructions Manual

Share
Download
Anchor Perfectshade Assembly Instructions Manual Download Page 8

PERFECT SHADE EMBEDDED IN CONCRETE

ALTERNATE INSTALLATION INSTRUCTIONS

When installing a frame that will 
be embedded in concrete, frame 
must be assembled prior to 
setting in concrete.

Step 1 Alternate

Using Dimension Chart in 
Step 1, dig (4) 1’-3” minimum 
diameter holes, 2’-3” deep or as 
required by soil conditions or 
local code.

Add 3” of gravel to bottom of 
holes.  (Bottom of pole must be 
allowed to drain water)

Frame may be assembled with 
uprights in holes.  See steps 5 
through 12 for frame assembly. 

When frame is assembled, 
plumb and level frame and 
brace into position.  

Fill concrete to ground level.  
Allow concrete to dry 72 hours 
before installing fabric.  See 
steps 13 through 22.

Note:  Concrete and gravel for 
setting uprights for embedded 
frame is required.  Installer to 
supply.

This page must be used in conjunction with standard Perfect Shade Installation Instructions

8

Summary of Contents for Perfectshade










Reviews:

No comments

Brands by name

Popular brands

Load more brands