background image

MAX77831 Evaluation Kit

Evaluates: MAX77831

w w w . a n a l o g . c o m

Analog Devices  │

 

19

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is 

assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that 

may result from its use.Specifications subject to change without notice. No license is granted by implicationor 

otherwise under any patent or patent rights of Analog Devices. Trademarks andregistered trademarks are the 

property of their respective owners.

REVISION

 

NUMBER

REVISION

 

DATE

DESCRIPTION

PAGES

 

CHANGED

0

9/20

Initial release

1

9/21

Updated 

General Description

 and 

Benefits and Features

 sections, 

MAX77831 

EV Kit Specifications

 table, Figure 2, updated 

EV Kit Default Configuration, Quick 

Start

, Table 1, Table 3, updated 

MAXUSB_INTERFACE#, External I

2

C Bus, High 

Temperature Testing, Critical Node Measurement (OUT and LX)

, and 

EV Kit 

Software

, added Figure 3 and Table 4, updated 

Windows Driver

 and 

Connecting 

GUI to MAXUSB_INTERFACE#

 sections

1–7

Revision History

Summary of Contents for MAX77831




















Reviews: