Anacon TUBEWONDER User Manual Download Page 2

page 2 of 22

© 2006, 2007 ANACON Technology 

IMPORTANT SAFETY INSTRUCTIONS 

BEFORE CONNECTING AND OPERATING THE APPARATUS - 

READ ALL OF THESE INSTRUCTIONS! 

 

• 

Save these instructions for later use. 

• 

Follow all warnings and instructions marked on the apparatus. 

• 

Keep this apparatus inaccessible to children and animals 

• 

Do not use this apparatus in tropical climate 

• 

Do not use this apparatus near water, i.e. bathtub, sink, swimming pool, humid 

basement, etc. 

• 

The apparatus must be used in horizontal position only. 

• 

Do not place this apparatus on an unstable cart, stand or table. A falling apparatus 

may suffer damage or inflict serious harm to persons! 

• 

Slots and openings in the cabinet front, back and top/bottom are provided for 

ventilation and heat dissipation to ensure reliable operation of the apparatus and to 
protect it from overheating. These openings must never be blocked or covered. 

• 

This apparatus should not be placed in a built-in installation unless proper 

ventilation is provided. 

• 

This apparatus should not be placed near a source of heat such as a stove, radiator, 

or another heat producing apparatus. 

• 

Use only the supplied power cord. 

Consult your dealer or local power company if you are unsure of the type of power 
available. 

• 

Do not allow anything to rest on the power cord. Do not place this apparatus where 

persons will walk on the cord. 

• 

Never break off the ground pin on the power supply cord. 

• 

Power supply cords should always be handled carefully. Periodically check cords for 

cuts or sign of stress, especially at the plugs or the point where the cord exits the 
unit. 

• 

The power supply cord should be unplugged when the apparatus is to be left 
unattended or unused for long periods of time. 

• 

Should this apparatus be mounted in an equipment rack, rear support should be 

provided. 

• 

This apparatus should be used only with a cart or stand that is recommended by 

ANACON Technology. 

• 

Never insert objects of any kind into this apparatus through cabinet slots as it may 

cause damage to sensitive parts and touch dangerous voltage points or short out 

parts that could result in risk of fire or electric shock. 

• 

Never spill liquid of any kind on or into the apparatus. 

• 

Do not place liquid containers of any kind on the apparatus. 

• 

Do not place any naked flame sources such as candles and the like on or near the 

apparatus 

• 

Do not attempt to service this apparatus yourself as opening or removing covers may 

expose you to dangerous voltage points and dangerously hot parts or other risks. 

Refer all servicing to qualified service personnel. 

• 

Unplug this apparatus from the wall outlet and refer servicing to qualified service 

personnel should any of the following occur: 

Power cord or plug is damaged or frayed. 

Liquid has been spilled into the apparatus. 

The apparatus has been exposed to rain or water. 

The apparatus does not operate normally when the operating instructions are 

followed. 

The apparatus has been dropped or the cabinet has been damaged. 

The apparatus exhibits a distinct change in performance indicating a need of 

service! 

• 

Adjust only these controls that are covered by the operating instructions. Improper 

adjustment of any other controls may result in damage and will often require 

extensive work by a qualified technician to restore the apparatus to normal 
operating condition. 

• 

Fuses: Replace ONLY with IEC127 (5 x 20 mm) type and rated fuse for best and safe 

operation! 

 

Summary of Contents for TUBEWONDER























Reviews: