AMX APEX Destiny 6100 Instruction Manual Download | Manualshive

Page: 10 / 18

background image

6

Installation and Wiring

APEX Destiny 6100 Alarm Panel

PHAST LCD keypads must connect directly to a PHAST Hub (or PHAST
Microphone Hub). Due to power requirements and/or the need for a separate
microphone line for each keypad, they cannot be daisy-chained to other LCD
keypads; they can, however be daisy chained with other PhastLink devices.

When connecting PHAST keypads that will be used as intercoms, the Microphone
Hub taps off the intercom audio signal carried on the PhastLink cable from that
keypad.

PhastLink devices cannot be wired in a star configuration.

«
...
8
9
10
11
12
...
»

Summary of Contents for APEX Destiny 6100



















Reviews:

No comments

Related manuals for APEX Destiny 6100

Brand: D-Link Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 33

Brand: Gateway Pages: 8

Subwoofer KHT2005.2

Brand: KEF Pages: 2

Brand: KEF Pages: 7

Brand: KEF Pages: 4

STExB2X05-S Series

Brand: E2S Pages: 20

Brand: Care Call Pages: 2

NAC-HD-329VL/60

Brand: Navaio Pages: 2

Brand: HAKO Pages: 6

Brand: Karaoke USA Pages: 32

Brand: R-Tech Pages: 19

Brand: Safe Signal Pages: 4

Brand: TRASSIR Pages: 2

Brand: Observint Pages: 24

Brand: LEGRAND Pages: 6

Brand: Fender Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands